5/8″ Type X is most commonly used for ceilings due not only for its rigidity (no sagging), but also its fire-resistance and acoustical blocking. You’ll certainly want to use at least 2-inch drywall screws to hang it. Not sure adhesive is necessary or recommended unless you are covering existing drywall.

How far can drywall span between studs?

Non-load-bearing walls can have vertical studs spaced as far apart as 24 inches, on-center. Since non-load-bearing walls only bear the weight of drywall and some electrical and plumbing work within, it is possible to have wider apart studs. In some homes, load-bearing walls are 24 inches apart, on-center.

How far can 5/8 drywall span unsupported?

5/8″ might span it, though you’ll end up with a lot of 6″ scraps due to 90 rather than 96″ spacing. 1/2″ not a chance – it will sag badly. If you strap it, you only need 1×3, and you don’t (IMHO) want it 24″ apart which is already a marginal spacing on ceilings – put it 16″ or even 12″ apart.

When should you use 5/8 drywall?

5/8-Inch-Thick Drywall These panels are commonly used for ceilings or for walls that require a prescribed fire-resistant rating. When installed on ceilings, 5/8-inch-thick panels are less susceptible to sagging between the joists than 1/2-inch panels.

How much does 5/8-inch drywall weigh?

A 4 x 8-foot sheet of standard 5/8-inch thick drywall weighs 74 pounds, and a 23 percent reduction in weight offered by ultralight can be significant.

What is code for hanging drywall?

Both the International Residential Code (IRC) and USG, the manufacturer of Sheetrock, note that the recommended maximum field screw spacing for wall drywall is 16 inches. Some builders like to space fasteners tighter than that, so they go down to 12 inches.

Is 5/8 drywall required for basement ceilings?

3 Answers. 5/8″ drywall is rarely required in single-family residences. It was used historically because ceiling joists are often 24″ on center, and 5/8 resists sag. You can certainly use no-sag 1/2″ if you like.

Why is there metal behind drywall?

Metal Plates In Walls Are Intended to Stop Drills So, as you’re probably aware, your wall hides some useful things, like pipes, electrical wires, and ductwork. Hitting any of these things when you drill into a wall would be bad.

What is the most common distance between wall studs?

Locate several studs and measure between them to confirm they have typical wall stud spacing of 16 or 24 inches. If you get a different measurement, you’ve likely located something other than a stud.

Can you hang drywall on 24 centers?

drywall thickness, lightweight is ideal for ceilings that have joists 24 inches on center. … drywall has always been approved for use on 24-in. spacing on ceiling framing, but because of heavy sagging insulation, wet ceiling textures, or higher humidity, either a 1/2-in. ceiling board or 5/8-in.

Article first time published on

Does thicker drywall help with sound?

So, here’s how thick walls should be to be soundproof: A standard stud wall built properly, and consisting of 2 sheets of drywall with an air cavity 5 to 6 inches thick, is good enough to make the wall soundproof. A concrete wall would have to be around a foot thick to be completely soundproof.

Does double drywall reduce sound?

Double Drywall benefits The benefit of a double thickness of drywall with Green Glue sandwiched between is less noise penetration. The drywall adds mass, which prevents sound wave penetration, especially lower frequency, and the Glue absorbs sound vibration-damping sound vibration movement.

Should I hang drywall vertically or horizontally?

Horizontal hanging reduces the lineal footage of seams by about 25%. Keeping the footage of seams to a minimum will result in less taping and a better looking finished job. Hanging horizontally also allows the drywall to flow over the framing so that bowed studs create less of a problem.

What is hat track?

A hat channel is a corrosion-resistant framing piece, which is used to fur out walls in masonry and ceiling projects. While it is most commonly used in basement renovations, it is used in other applications as well. … Hat channels contain a grooved metal piece which is perfect for levelling out walls.

What is the maximum recommended spacing for 5/8 inch drywall installed on a wall at right angles to framing members?

THICKNESS OF GYPSUM BOARD OR GYPSUM PANEL PRODUCTS (inches)APPLICATIONMAXIMUM SPACING OF FRAMING MEMBERS (inches o.c.)5/8Ceiling16Ceiling24Type X at garage ceiling beneath habitable rooms24Wall24

How long should drywall screws be for 1/2-inch drywall?

Choosing the right drywall screw Most common — 1-1/4”: Use 1-1/4” drywall screws to secure 1/2″ drywall installed on wood-stud walls. These coarse-thread screws typically feature phosphate coatings, which better protect against rust compared to zinc coatings.

What happens if you don't stagger drywall?

Time – It takes longer to stagger sheetrock than to align panels in parallel. … The wall length and ceiling area must be calculated, and staggering or not staggering the sheetrock may impact how many panels are needed to complete the job. Purpose – The type of finished job should be considered when hanging sheetrock.

How much does a 4x12 sheet of 5/8 drywall weigh?

While the weight of drywall at 5/8” thickness is about 2.31 pounds per square foot. However total weights in lbs may differ by size and by brand. By the sheet, standard drywall sheeting comes in at: 4′ by 8′ by ½ is close to 52 pounds 4‘ by 12’ by ½ is close to 77 pounds.

How many sheets of drywall can a truck hold?

Registered. 3800 LBs is what I have driven over 200 miles in my 2500 so I am confident in that number especially across town just remember it will take a little more distance to stop. it figures out to be about 42 sheets as they weigh about 2.8lbs per sqft.

What's the difference in sheetrock and drywall?

Drywall is a flat panel made of gypsum plaster sandwiched in between two sheets of thick paper. It adheres to metal or wood studs using nails or screws. Sheetrock is a specific brand of drywall sheet. These terms are often used interchangeably.

What is purple drywall?

Our most versatile drywall product, PURPLE XP® Drywall is moisture-, mold- and mildew-resistant and ideal for almost every room in the home. Performance. Fire Resistant, Improve Air Quality, Mold & Mildew Resistant, Moisture Resistant. Project Area.

Can you use 3/8 drywall ceiling?

Joe, yes you can use 3/8-inch drywall on ceilings like this. … It’s the BIBLE of everything drywall and plaster. In this great book you’ll find the minimum recommendations for installing 3/8-inch drywall, including fasteners, spacing, etc.

What drywall is best for basement?

Due to the often damp conditions of the basement, be sure to choose sheetrock that is at least moisture-resistant (often call greenboard) but be on the lookout for products that are specifically resistant to mold and mildew (some kinds of purple board).

Should drywall touch the floor?

Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods. Wear work gloves, safety goggles and a dust mask when hanging drywall.

How many screws go into a 5lb drywall box?

How Many 1 5/8” Drywall Screws Per Pound? There are approximately 189-200 drywall screws or fasteners of 1 ⅝ inch length in a one-pound package. A five-pound box of 1 ⅝ inch drywall screws will be a total of 945-1,000.

What size screws 5/8 drywall?

Installation Considerations When working with 5/8-inch drywall panels, use 1-3/8-inch or 1-5/8-inch screws. To properly secure drywall, the right number of drywall fasteners should be used.

Is there a stud in every corner?

Studs exist to hold up drywall on interior walls and wood sheathing on exterior walls. This means you will always find a stud, header, or footer on the top, bottom, or corners of walls. … Most electrical boxes for switches or outlets are attached to a stud on one side. There are studs on either side of a window.

Why are studs spaced 16 on center?

When you put studs on sixteen inch on center four foot and eight foot material will break on the studs like it will with two foot on center and add an extra stud per four foot. What this accomplishes is to make the wall covering material more stable and less likely to warp and distort over time.

Why can't I drill into brick?

However, if you have old, fragile brick and you’re mounting a heavy object that requires deep holes and expansion-style anchors, drilling into the brick may not be the best choice. Deep holes weaken the brick and expansion anchors can create enough circular stress to crack the brick.

Why can't I drill into a stud?

The reason why you can’t drill through a stud could be a dull drill bit, failed drill battery, wrong drill rotation direction or an impenetrable metal/steel member of the wall structure.

How many times can you drill into a stud?

To appease the plumbing gods, the codes have made at least one notable exception: In bearing walls you can bore 60 percent size holes—as long as you double up the studs and don’t drill through more than two successive pairs of these doubled-up studs (Fig. A).