To determine the needed lumens, you will need to multiply your room square footage by your room foot-candle requirement. For example, a 100 square foot living room, which needs 10-20 foot-candles, will need 1,000-2,000 lumens. A 100 square foot dining room, which needs 30-40 foot-candles, will need 3,000-4,000 lumens.

What length LED lights should I get for my room?

How Long Should LED Lights Be for a Room? If you’re adding LED strip lights or string lights, you can look for a standard 16 foot roll or a strip light that can be connected together to make a longer run. Most standard sized bedrooms are around 12 feet by 12 feet or even smaller.

How do I calculate how many LED downlights I need?

How Many Downlights Do You Need To Install? By dividing the light intensity suggested for each room into a single light, you will get the number of components required to adequately illuminate your space.

How do you calculate the amount of light needed in a room?

Multiply width of room x length of room x 1.5 = amount of total minimum wattage needed (assuming an eight foot ceiling). Divide by 60 to get the number of 60-watt equivalent bulbs required. Then, add up the wattage in each bulb in each fixture to figure out how many light fixtures are needed.

How many watts of light do I need for my room?

Multiply the width by the length for each room or room segment, if applicable. Multiply the result by 1.5 to determine the estimated watts to sufficiently light a room. For example, for a room 10 feet wide by 12 feet long, multiply 10 times 12 to get 120, then multiply by 1.5 to get 180 watts.

How is LED light size measured?

The luminous intensity (unit: candela) of LEDs can be measured with a conventional photometric bench and the standard photometers [2] under a far field condition, at a distance far enough so that the test LED can be regarded as a point source (typically 2 m or longer).

What is 5050 LED strip?

The 5050 is an RGB strip whose chips measure 5.0mm by 5.0mm. They have 3 LED diodes in each casing called tri-chips, which gives them a very bright glare when turned on at full power. … The 5050 LED uses about 60mA of power, has a surface area of 25mm squared, and a brightness of 22 lumens.

How many lumens does a 15 watt LED bulb produce?

Lumens for Light Source WattsLumensIncandescent WattsLED Watts800601211007515160010020

How do you calculate lumens per watt LED?

For example, a 100 W incandescent bulb produces about 1,600 lumens, for an efficiency of 1,600/100 = 16 lumens per watt. A halogen bulb, on the other hand, consumes only 72 watts for the same amount of brightness, making its efficiency 1,600/72 = 22 lumens per watt.

What led wattage for bedroom?

The best light bulb for a bedroom is one that sends out around 800 lumens. This is the same as an older lightbulb (incandescent, not LED) of 60 watts. At 800 lumens, the light will be bright enough to read by but won’t be so bright that it makes you too alert that you’ll have a hard time falling asleep.

Article first time published on

How much space do you need between downlights?

Recessed downlights are generally positioned 1.5 to 2 ft. away from walls with a space of 3 to 4 feet between each light. Dividing the ceiling height by two is a way of gauging how much space to leave between each downlight. Thus, if your ceiling is 8 foot high, place your lights 4 feet apart.

How many downlights do you need per room?

A general rule of thumb you can go by is around 1 downlight per 1.4m2 of coverage at an average roof height for an adequate cover of light.

How many lumens are in a m2?

The current regulations indicate that to illuminate an office, for example, we recommend about 300-400 lumens per square meter of surface. Therefore, if your goal is to illuminate an area used as an office whose surface is 100 square meters, the light potency you will need will be around 30,000-40,000 lumens.

WHAT LED bulb is equivalent to 100 watt?

Incandescent Light Bulb WattageLED Equivalent Wattage100 Watt10 Watt75 Watt7.5 Watt60 Watt6 Watt50 Watt5 Watt

Is 60 watts enough to light a room?

For a room with decent natural light, that should be around 60 watts. For a room with few/no windows, balance the 60 watt desk light with ambient overhead lights or bump that number up to 75 watts. … So two 40 watt bulbs in a pair of sconces or three 30 watt bulbs above the mirror for example).

Can I put a 100W LED bulb in a 60w?

However, LED’s do not emit dangerous levels of heat. Thus, if your fixture says “not to exceed 60-Watts” but you want to use a 100-Watt equivalent LED bulb, this would be safe to do so. … For a 60-Watt fixture, you could use a 100W, 125W, or even 150W LED equivalent because they all consume under 60-Watts!

Which is brightest LED strip?

SMD (Surface Mounted) 5730 series is the brightest LED strip because it contains powerful LEDs that can create a lot of light.

Which is brighter LED 5050 or 3528?

5050 chips are typically 3 times as bright as 3528 chips. Because they’re brighter, strips with 5050 chips are typically used for what we call ‘task lighting’, and commonly used underneath kitchen cabinets where that light will help you see what you’re working on.

How do I identify LED Strip Lights?

An LED strip description often includes a 4-digit number such as 5050 or 2835. The number usually describes the size of the chip. For example, a 5050 LED chip measures 5.0 mm wide by 5.0 mm tall. Similarly, a 2835 chip measures 2.8 mm wide by 3.5 mm tall.

How is LED luminance calculated?

Luminous intensity measures the quantity of visible light emitted in a given direction at solid angle by a light source, the unit of luminous intensity is candela (cd). The equation to calculate lumens, when candelas and solid angle of a light source are known is: 1lm = 1cd * sr.

How do you measure LED intensity?

To measure light intensity from LED lighting, you would use an LED light meter. LED lighting has become increasingly common in commercial environments because of energy-efficiency, longevity, color temperature tuning, safety, and low maintenance.

How much current does a 3mm LED use?

ColorBlueWavelenght465-470 nmMax forward current20 mA (continuous)Foward voltage2.8 VDC (typ)View angle55-65 degree

What is 18W LED equivalent to?

Lumens (Brightness)LED Watts (Viribright)CFL Watts400 – 5006 – 7W8 – 12W650 – 8507 – 10W13 – 18W1000 – 140012 – 13W18 – 22W1450-1700+14 – 20W23 – 30W

How bright is a 15W LED light?

LED light bulbs for general use around the home will typically have a wattage between 5W-15W, and will emit between 300-500 lumens.

What is 40 watt LED equivalent to?

Traditional bulb1Halogen2LED40 watts25 watts5 watts60 watts40 watts7 watts75 watts45 watts9 watts100 watts60 watts12 watts

How many lumens is a 12x12 room?

As a handy rule of thumb, a sitting room or bedroom will generally require around 10-20 lumens per square foot, while a bathroom or kitchen will need a stronger level of lighting, at around 70-80 lumens per square foot. To work out the lumens you need, simply multiply the square footage of the room by this figure.

How is LED wattage calculated?

To calculate an LED’s power use, simply multiply the LED’s voltage (in volts) by the LED’s current (in amperes). The result, measured in watts, is the amount of power your LEDs use. For example, if your LED has a voltage of 3.6 and a current of 20 milliamperes, it will use 72 milliwatts of power.

What is a 17 watt LED bulb equivalent to?

Philips recently released its Ambient LED 17/75-watt-equivalent retailing for $39.97. As it indicates, the bulb gives off roughly the equivalent light of a 75-watt incandescent bulb, but uses only 17 watts of power to do it.

Is 9W LED bright enough?

If you use energy-saving lamps, take a 10㎡ bedroom as an example, 9W is enough. Of course, you can also choose some small ceiling lights, which can not only increase the beauty, but also control the intensity of the light source.

Is 3w LED bright enough?

The new type of superbright LED lights available today produce about 100 lumens per watt of power input. … We can now see clearly that a 3 watt LED spotlight would produce 300 lumens, not 600 lumens, so definitely not equivalent to a 50 watt halogen bulb.

How bright is 9W LED bulb?

9W LED (800 lumens) replaces a 60W bulb or 14W CFL.