Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.

How do you reset the spin cycle on a GE washer?

Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.

Why won't my GE washer agitate or spin?

Make sure the washer lid is down. … Most models have either a lid switch probe or a magnet on the lid that activates the lid switch when the lid is closed. If the lid switch probe or magnet is missing or damaged, the washer will not agitate or spin, even with the lid closed.

What is wrong with my washing machine when it won't spin?

Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.

Do GE washers have a reset button?

To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.

Why does my GE front load washer not spin?

The first thing to check when a GE front load washer won’t spin is the belt and pulley. Remove the back panel off the washer to access the belt and pulley. Check to see if the belt is worn or broken and if so, replace it. … If this is the case the pulley will have to be replaced.

Why does my GE washing machine stop mid cycle?

Common solutions for: GE Washer stops mid cycle If the washer door is not latched shut, the door switch prevents the washer from operating. If the door lock is defective, the washer may stop mid cycle. … Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.

Will washer work without lid lock?

NO. The lid lock it to prevent injury to the people near the washer, as without it stopping the machine, the agitator will turn with the lid open. So. If you will open the top up, you should see the lid switch, and you should see the electric wires attached to it.

How do I know if my GE washer lid switch is bad?

Signs The Lid Switch Is Bad If the control panel doesn’t detect the switch as being engaged, then the washer won’t agitate or spin when you close the lid. Your washer may or may not fill with water when you have a bad lid switch depending on the model you have.

Can you bypass a washing machine lid switch?

Most washing machines come equipped with a lid switch. This switch is connected to a solenoid that completes a circuit, allowing the machine to run only if the top is down. … A simple bypass for the first type of lid switch is to simply jam a piece of wood into the switch, causing it to activate the solenoid.

Article first time published on

Why won't my GE washer fill?

Machine Won’t Fill If your washer won’t fill, check the hot and cold faucets to make sure they’re both turned on fully. … Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.

Where is the lid switch on my GE washer?

General Electric, or GE, top-loading washing machines have a lid switch located on the door jamb of the top of the cabinet. The switch is compressed by the lid when the lid is closed and decompresses when the lid is open.

What do you do when your washing machine stops mid cycle?

Try stopping the machine, draining the water and rearranging the laundry. The spinning cycle won’t start if the water hasn’t drained completely. Turn off your washing machine and check the drain hose and the pump filter. The hose shouldn’t be bent or clogged.

How do I unlock my GE washer door?

If the washer is running, press the START/PAUSE button once it will pause the washer and unlock the door. It will take a few seconds for the door to unlock after pressing PAUSE. Press again to restart the wash cycle. In some cycles the washer will drain first, and then unlock the door when it is paused.

How do you bypass a washing machine door lock?

One of the main ways of bypassing a washing machine door lock is by disabling the safety circuit. It is good to note that the process involves cutting of electrical wires. Thus, you need to disconnect your machine from the main power supply. Additional, cutting the cord may void your warranty.

What is a washing machine lid switch?

This is the lid switch. It’s usually found just under the washer’s top, where it can be activated by a small rod on the washer lid, which pushes the switch when the lid is down. … If it does, when the machine reaches the spin cycle nothing will happen, since the machine ‘thinks’ that the lid is open.