Open the dishwasher door and quickly close it. … Locate the “On/Off” button on the left side of the dishwasher control panel. … Select and run a dishwashing cycle to ensure that the dishwasher control board has been reset successfully.

Do dishwashers have a reset button?

Yes, you can reset your dishwasher by pressing the Start/Reset button on the appliance and waiting a few minutes. If your dishwasher still doesn’t start, you may need to reboot the entire system by turning off power to the appliance at the house circuit breaker or fuse box.

How do you program a Smeg dishwasher?

STARTING THE PROGRAM To start the dishwasher, press the START/PAUSE button (6) for a few seconds, until the light of the selected program starts to flash (confirmation beep). The light will flash as long as the program is in progress, to indicate that it is being performed.

Why is my Smeg dishwasher flashing?

The light flashes to indicate that the appliance is in “water hardness adjustment” mode. SALT WARNIN LIGHT (on some models only) If the symbol is present, illumination of this light denotes a regenerating salt warning level.

Why would I reset my dishwasher?

There are many reasons why a dishwasher needs a reset, from a simple issue with a dirty door lock to a bad button push. Check the breaker and power source before calling a repair technician or replacing the item entirely.

Why is my Smeg dishwasher not starting?

The Basics. A Smeg dishwasher not starting could simply be a problem with the power supply – the appliance won’t start if water is unable to be drawn from the mains water supply. … And then the dishwasher should verify the setup and start of a wash cycle. If this isn’t happening the power outlet itself may be at fault.

How do I reset my dishwasher?

Resetting your dishwasher is easy. Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the dishwasher (usually 1 to 5 minutes at most), and then power it up again. That’s it. That’s all it takes to reset.

What does Error 01 mean on a Smeg dishwasher?

Aquastop floating intervention – Water Leak If your Smeg dishwasher is showing an E01 or an E02 error code on the display, the possible cause may be that water is leaking in the base of the machine. … if there is not water in the tray, check that the floater keeps closed the switch for a wrong positioning.

Why is my Smeg dishwasher not getting water?

Your dishwasher may not be filling with water simply because the water valve’s filter screens are dirty and debris-filled. Gain access to your water inlet valve and try cleaning it out. This might be enough to solve the problem. … Alternatively, your water inlet valve could be defective altogether.

What is the red light on Smeg dishwasher?

Certain dishwasher models have been fitted with the ActiveLight system. This consists of a red LED light which projects a red spot onto the floor beneath the dishwasher door when the appliance is in use, meaning you don’t have to open the door to check that it is running. The light goes out when the wash concludes.

Article first time published on

What Smeg dishwasher do I have?

The Smeg model number is located on the lower part of the Smeg hob which is fixed to the casing. In order to read it, you must access the lower part. A copy of the label is included with the instruction booklet.

How do I open my Smeg dishwasher?

To open the door on an integrated dishwasher from new, ie: without the decor door fixed, there is a hand hold top centre of the door, insert hand and give the door a sharp pull towards you. the door will spring back up due the the missing weight of the decor door.

What does the P mean on a dishwasher?

Pre Rinse. A short rinse cycle used before a full wash cycle. Useful for loosening dried on food remains and when dishes have been left for a while.

How do I reset my dishwasher control panel?

How Do I Reset My Dishwasher Control Panel? Simply unplug your dishwasher. Wait for one minute, then plug it back in again, to reset the dishwasher control panel.

Why won't my dishwasher lights come on?

If there’s no light in your dishwasher’s control panel, the first thing you should do is to check that the machine is connected properly to the power source in the wall. If it’s properly plugged in, you should confirm that the outlet works by plugging another appliance into it.

How do you remove the kick plate from a Smeg dishwasher?

1. Inspect the toe kick plate on the bottom of the dishwasher for screws. …
2. Remove the toe kick plate screws with a Phillips-head screwdriver or Torx #20 screwdriver.
3. Slide the toe kick plate away from the dishwasher. …
4. Locate the access panel just above the toe plate.

What does E01 mean on a dishwasher?

What Does the E01 Code Mean? This code indicates that there is a problem with the rinse cycle that is supposed to take place once the wash cycle is complete. If the water inside your dishwasher is not properly restored, this error will appear. In other words, not enough water is entering the appliance.

Where is the float on a Smeg dishwasher?

Your float assembly is found inside the dishwasher’s tub, on the bottom.

How long does Smeg dishwasher take?

Smeg dishwashers have several pre-set programs to choose from. A basic wash and rinse can take as short as 27 minutes while a thorough cleansing with anti-bacterial washing and rinsing can extend to 2.5 hours.

How do I read my Smeg serial number?

The Smeg model number is listed as a ‘MOD’ number and is a combination of letters and numbers (e.g. SUK62MFX5). The Smeg serial number is listed as a ‘N’ or ‘S/N’ number and is an 8 to 10 digit number (e.g. 108 51423).

Is SMEG a reliable brand?

Smeg has a reputation as a luxury brand, but it doesn’t always deliver bang for your buck. Its fridges are priced at the very upper end of the market, but they’re made by the same company that produces Beko fridges, which fall at the lower end of the price scale and often don’t perform well in our tests.