Reset The Reset button serves two functions for the UniFi AP: • Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.

How do I factory reset my ubiquiti AC Pro?

Reset The Reset button serves two functions for the UniFi AP: • Restart Press and release the Reset button quickly. Restore to Factory Default Settings Press and hold the Reset button for more than five seconds.

How do I access my ubiquiti access point?

Windows users: Start > All Programs > Ubiquiti UniFi. 2. The UniFi login screen will appear. Enter the admin name and password in the appropriate fields and click Login.

How do I reset my ubiquiti to factory settings?

Reset Button This button serves two functions for the UniFi Switch: • Press and release the Reset button to restart the device. Press and hold the Reset button (for at least five seconds) to restore the device to its factory default settings.

How do I reset my Ubiquiti AP LR?

(In case powered by the POE adapter, make sure the cable on the LAN port of the adaptor is unplugged.) After they’ve booted, press and hold the small reset button (located on the back of the device) for 25+ seconds. This should reset the UniFi APs and put them back into a discoverable state again.

What is the default IP for Unifi AP?

Be sure to have a network that is of the 192.168. 1. X scheme if you are connecting to the AP using its default IP of 192.168. 1.20.

How do I reset a ubiquiti switch?

1. Power off the device. Just unplug the power cable.
2. Forget the device in the controller. …
3. Unplug all network cables. …
4. Plug power back in. …
5. Wait until the led turns dark blue. …
6. Press the reset button for 5 seconds. …
7. Adopt the device in the controller.

How do I reset my ubiquiti password?

1. Go to account.ui.com and click Forgot password?
2. Enter the email address associated with your account and send yourself a password-reset email.
3. Click the link in the email to create a new password.

How do I reset my ubiquiti PowerBeam?

Technology Page 4 Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the PowerBeam is powered on. Alternatively, the PowerBeam may be reset remotely via a Reset button located on the bottom of the PoE Adapter.

How do I reset my ubiquiti access point?

1. Log in to the Unifi Controller.
2. Click on the Devices Tab.
3. Click on the Access Point you wish to restart.
4. On the right-hand side fly in click on the tools icon.
5. Scroll down and click on Open Terminal.
6. On the terminal that opens type in reboot and hit enter.

Article first time published on

How do I change my UniFi AC Pro password?

Go to Settings (the gear icon in the bottom-left of the page). Go to the Site section (this is the default section you go to when going to the Settings page). Make the desired changes in the “DEVICE AUTHENTICATION” section at the bottom of the page. Click the “APPLY CHANGES” button.

What is the default username and password for Ubiquiti UniFi?

The default username is ubnt and the default password is ubnt.

How do I know if my UniFi is working?

Blue Indicates the device has been successfully integrated into a network and is working properly. Quickly Flashing Blue This is used to locate an AP. When you click Locate in the UniFi Controller software, the LED on the AP will flash.

How do I force adopt UniFi AP?

1. Launch the Network web application from unifi.ui.com.
2. Open the UniFi Devices page.
3. Select the device that is ready for adoption.
4. Click Adopt.

How do I reset my UniFi USG?

Resets to factory defaults. The UniFi Gateway should be powered on. Press and hold the Reset button for about 10 seconds until the right LED on the WAN 2 / LAN 2 port starts flashing and then becomes solidly lit. After a few seconds, the LED will turn off, and the UniFi Gateway will automatically reboot.

How do I reset my ubiquiti air cube?

The LED lights up when the airCube is powered on. Resets to factory defaults. The device should be running after bootup is complete. Press and hold the Reset button for about 10 seconds until the LED starts flashing and then becomes solidly lit.

How do I reset my Ubiquiti airMAX?

Press the reset button on the device. While holding the reset button down, power the unit on. Wait 8 seconds then release the button (if you want to reset the unit to factory defaults, wait about 15 seconds or until the signal LEDs light up to indicate that the device is ready for recovery).

What is the IP address for Ubiquiti router?

In the factory default state, the EdgeRouter is accessible on the 192.168. 1.1 IP address on the eth0 interface. Refer to the sections below for more information on how access the EdgeRouter using either the Web UI, CLI or Console connection on different operating systems.

Can I use Ubiquiti access point without controller?

UniFi APs can run by themselves without the controller unless features like guest portal is enabled (as UniFi controller also functions as a captive portal). Restarting the controller won’t restart your APs.

How do I log into Ubiquiti WIFI?

Windows users: Start > All Programs > Ubiquiti UniFi. 2. The UniFi login screen will appear. Enter the admin name and password in the appropriate fields and click Login.

How do I know my UniFi password?

Right click on the wireless network adaptor and select Status. Click the Wireless Properties button. In the Properties dialog that appears, move to the Security tab. Click the Show characters check box, and the network password will be revealed.

How do I know my UniFi account number?

Login to your Selfcare, and then click Dashboard. Under Dashboard, your account number is shown just below Credit Limit.

How do I change my UniFi WIFI name and password?

Using Basic Wireless Settings or In Wireless Network Name (SSID) box, enter your preferred WIFI name. In Password box, enter your new WIFI password.

How do I reboot my access point remotely?

1. Remove the power and replug the power cable.
2. Using the CLI in the ap prompt type boot command. i.e [ap:boot]
3. In the Web interface use the System Configuration Setup page to restart the access point. Use the System Configuration Setup page to restart the access point.

How do I reset my ubiquiti cloud key?

Power off the system. Press and hold the reset button and then power on the Cloud Key by connecting it to the power source. Keep the reset button pressed for about 10 seconds, or until you see the recovery LED pattern in a loop (blue – off – white).

How do I SSH into an UniFi AP?

Force Adopt Open your favorite SSH client (PuTTY for windows) or Terminal on any other OS. Use the IP address for the AP found in DHCP to SSH into the AP with the default user/password provided ubnt/ubnt or root/ubnt. Next you will receive a splash screen of ASCII text saying UniFi and be at a command prompt.

How do I reset my NanoStation M2?

Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the NanoStation is powered on. Alternatively, a remote reset button is located on the bottom of the PoE Adapter.