For pools 4′ deep or less, use 1 hose weight 4″ to 12″ from the cleaner. For pools of 4-7′ deep, use 2 weights, one 4″ to 12″ from the cleaner and one 6′ from the cleaner. For pools from 8′ to 12′ deep, use a third weight, placed 10 ft. from the swivel end of the cleaner.

How do you adjust the weight on a Kreepy Krauly?

For pools 4′ deep or less, use 1 hose weight 4″ to 12″ from the cleaner. For pools of 4-7′ deep, use 2 weights, one 4″ to 12″ from the cleaner and one 6′ from the cleaner. For pools from 8′ to 12′ deep, use a third weight, placed 10 ft. from the swivel end of the cleaner.

Why does my creepy crawly stay in one spot?

This can happen for a number of reasons, for example: You have taken your hose out of the pool and stored it. It coiled. Over time the top layer of your pool water has slowly reset the memory of your hose.

How do I change the speed on my Kreepy Krauly?

If that doesn’t slow down the Kreepy cleaner enough, you can adjust the regulator valve. To decrease the speed of Kreepy Krauly, open up the manual bypass fully, on the bottom of the regulator valve. The regulator valve fits in between the skimmer and the Kreepy hose. Press it into the threaded compression adapter.

Why does my Kreepy Krauly not sit flat?

It’s all about getting the right amount of flow through the diaphragm so it levels out and works right. That adapter allows for adjustments due to different sized pumps so it can ge dialed in for more or less suction. Well I did install the part where I can control the suction and it still doesn’t want to lay flat.

What do pool hose weights do?

Simply put, you need to add weight to your pool cleaner in order to keep it on the pool floor and assist it in reaching certain pool areas. … Hose weights help to keep the head of the cleaner flush with the floor of your swimming pool and able to suck up all the dirt that makes its way there.

What are hose weights for?

Just Add Hose Weights Hose weights come in different gauges and colors. With the hose held 2 inches below water, the Solar-Breeze NX will continue to skim the surface. This reduces the hours per day that you need to run your pump, filter and bottom cleaner.

How long does a Kreepy Krauly last?

The Kreepy Krauly is an extremely durable cleaner with very long lasting parts. The only parts that wear out on a regular basis is the Foot Pad and the rubber Seal. The Foot Pad will last you one to two years depending on how ruff your pool surface is. The Seal should last you at least 2-3 years.

Why is my creepy crawler not working?

The most common cause for a Kreepy to stop working is clogged filter sand. This is easy to diagnose because whenever you backwash the pool filter, you’ll find that the Kreepy works like a bomb for 10 minutes. Then it gets sluggish and slows down or stops again.

Why does my kreepy krauly stay in the deep end?

Usually if the Kreepy Krauly is staying in one end of the pool the problem is 1 of 3 things. The flow of water from the return is keeping the KK in one area, or the hose may not be the correct length, or the hose may not have the correct balance.

Article first time published on

Why does my kreepy krauly flip over?

Check your weight placements. Your hose is either too light and floating up and flipping over or too heavy and sinking and rolling over. … To keep the unit lower and off the wall I re added the weight to the very end of the hose where the hose plugs in to the cleaner. This solved my issue of flipping over.

How do I increase the pressure on my pool pump?

1. Fill the water up to the proper level with a garden hose. Pool pressure is affected by low water levels. …
2. Clean out the skimmer basket of the pool. …
3. Turn the filter off and open the pool pump. …
4. Inspect pool hoses for cracks and leaks.

How does the Flowkeeper valve work?

LOCATE FLOWKEEPER VALVE – The Flowkeeper Valve regulates flow to ensure the pool pump and Zodiac X7 Cleaner run properly. It is pre-set at the factory at “2” to optimize the performance of the Cleaner. Two other settings are offered. The lower the setting number, the lower the flow.

What setting should my pool pump be on to vacuum?

For routine vacuuming, the filter valve is left in the normal “Filter” position. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. The “Filter” setting is used for light to moderate levels of pool sediment.

Why is pool cleaner not moving?

If you have a suction pool cleaner that is not moving, check the cleaner hose. It should be firmly attached to the suction line in the skimmer or the cleaner line. … For these types of pool cleaners, the culprit is usually a problem with the hoses that are either clogged or not connected properly.

Should pool hose float?

The hose will be floating in the water when you first out it in the pool. … As you force the air out and the water in the heavy pool vacuum head will float to the surface of the pool from the bottom of the pool. The pool hose will fill with water and sink to the bottom and the vacuum head will also sink to the bottom.

How long should I run pool vacuum?

Manual Model A manual vacuum should be run as long as it takes to remove all visible dirt and debris on the bottom and sides of the pool. For a small, well-maintained pool, this usually takes around 20 minutes. For a very dirty small pool, or a maintained larger pool, it may take around 45 minutes.

How do pool creepy crawlers work?

Without a Kreepy Krauly the pool water is drawn only from the top of the pool. A Kreepy Krauly draws water from the bottom, top and sides of your pool ensuring circulation of pool water and improving water quality. This helps remove biological particles and fine particles that can cause your pool to look cloudy.

How long should my pool cleaner hose be?

Measuring the ideal length for your hose is a matter of calculating the distance of the two furthest points in your swimming pool. So, for example; If your skimmer is located 30 feet from the furthest corner, and your pool has a depth of 5 feet, you will need a 35-foot-long vacuum hose.

Why does my pool vacuum keep stopping?

When a suction cleaner is sluggish or slow, it’s usually a clogged pump basket or dirty filter that is to blame. Other problems include holes in the cleaner hose, sucking air into the hose, or the filter pump could be drawing in air, reducing water-flow volume.

Why does my Zodiac pool cleaner keeps stopping?

If your Zodiac pool cleaner stops and starts, the first thing you might want to do is check the suction flow coming through the hose. You will need your pump on for this operation. … Once we’ve done that and the pool cleaner still isn’t working properly, then we might want to check the hose for leaks.

What is the best creepy-crawly pool cleaner?

• Our Top Pick. Kreepy Krauly Suction-Side Automatic Inground Pool Cleaner. $336.98. …
• Our Top Pick. Pentair Kreepy Krauly E-Z Vac Suction-Side Above Ground Pool Cleaner. $168.99. …
• Lifetime Extra Large Deck Storage Box. $179.00.

Where does the flow director go on the Lil Shark?

the flow director goes on the return port to push the water by the wall instead of in to the pool.

What's a creepy-crawly?

Definition of creepy-crawly informal. : an unpleasant worm, insect, or spider a basement full of creepy-crawlies.

How often should you run a kreepy krauly?

Ideally, you need to run your robot pool cleaner daily or at least once a day if you’re always swimming in it. But if you don’t swim in it as much, run it at least once weekly or every two weeks. When you’re using a swimming pool cover all the time, you may wash your pool monthly.

How often should I backwash my inground pool?

As a general rule, you should be backwashing your pool about once a week or in conjugation with your scheduled maintenance. Another industry standard is to backwash when your filter’s pressure gauge reads 8-10 PSI (pounds per square inch) over the starting level or “clean” pressure.

How does a weir valve work?

The Auto Flo Weir Valve works by regulating the flow through the pool cleaner to the pump. As the filter collects debris, the valve will automatically maintain the correct flow.

Why does my pool cleaner go in circles?

Sometimes it gets stuck in the corner of the pool by the steps; other times it goes in circles. … This is most likely caused when pool cleaners are left in the pool 24/7. When the water is cold or cools off from a warm day, the plastic in the hose gets a memory and curls slightly.

Why is my pool filter pressure so low?

When the pressure is lower than normal, this usually indicates a flow problem, and usually something is blocking or restricting water flow into the pool pump. It’s never a problem after the pool pump, because after the impeller, the pool water is under pressure, and obstructions result in higher than normal pressure.

Why is my pool pump not getting pressure?

It could be a clogged pump basket, clogged impeller, clogged pipe or clogged skimmer. It could also be a closed or broken valve before the pump. Or, the pump may have an air leak, and is drawing in more air than water, which will also reduce the filter pressure (and filtration).