One gallon of ADVANCED DECKOVER Coating can cover up to 75 Sq. Ft. with 2 Coats. It is strongly recommended to fill cracks, nail holes and accessible board ends prior to applying the first coat.

How many coats should Behr deck over?

One gallon of ADVANCED DECKOVER Coating can cover up to 75 Sq. Ft. with 2 Coats. It is strongly recommended to fill cracks, nail holes and accessible board ends prior to applying the first coat.

How do you use Behr Premium Advanced Deckover?

Stir product occasionally throughout application. DO NOT THIN PRODUCT. For nail holes and cracks up to 1/4″, completely fill in with DeckOver coating using a nylon/polyester brush and allow to dry prior to rolling. Deep nail holes and cracks may require additional filling.

How long does Behr Deckover last?

If the DECKOVER coating is applied according to label directions to a properly prepared, sound wood or concrete substrate, the film can be expected to last as long as a high quality Solid Color Wood Stain. BEHR Solid Color Wood Stains last 5 to 10 years on horizontal surfaces and 15 to 25 years on vertical surfaces.

How long does it take Deckover to dry?

Dries to touch in 4 hours. Wait 24-48 hours before light foot traffic. 72 hours to full cure. Additional dry time may be needed in cooler temperatures and higher humidity.

How long does Deckover need to dry before rain?

If the coating was applied and was exposed to rain 24 hours after application or later, it should be ok. However, for best results, it would be ideal to allow the coating to fully cure for 72 hours (at least) before allowing moisture to come in contact with the finish.

Can you use Deckover on pressure treated wood?

Hi Louise, DECKOVER can definitely be used on newly pressure treated wood, as long as all label instructions are followed. … We do not recommend pressure washing, but definitely clean the new pressure treated wood before applying DECKOVER.

What is better than Behr Deckover?

Deck Resurface Stains like Behr Deckover, Olympic Rescue-It, Rust-Oleum Restore – Do They Work? … They claim it is the smart alternative to deck replacement. It can be applied to wood surfaces such as decks, stairs, docks, composite decking, and more.

What happens if you paint your deck and it rains?

If it rains within 48 hours of applying a treatment, the water will soak into the wood, and try and displace the stain. This can cause a blotchy, flaky look, rather than a smooth, even, coat. If it rains immediately after you’ve stained the wood, the stain will peel and flake off.

Is Deckover a good product?

This 100% acrylic formula conceals cracks and splinters up to 1/4″, and creates a smooth, slip-resistant finish that also resists cracking and peeling. It’s available in 54 solid custom colors and is also great for decks, railings, patios, composite decks, pool decks, and walkways.

Article first time published on

How do you remove peeling from Behr Deckover?

The only good part about the peeling DeckOver was, it ended up being relatively easy to remove. Much of it came up just with our fingers- we could literally just pick it up and peel it off. What we couldn’t peel off with our hands, we used a scraping tool and would pry an edge off, then peel it off.

How long before you can walk on deck over paint?

In most cases a full body stain or acrylic deck finish will be dry to touch within an hour in dry, hot weather. After two hours you could take a chance and walk on it with shoes, though I’d recommend barefoot. After about 4 hours you should be able to safely walk on your deck.

How long does Behr Deckover take to dry?

Dries to touch in 4 hours. Wait 24-48 hours before light foot traffic. 72 hours to full cure. Additional dry time may be needed in cooler temperatures and higher humidity.

Why is my deck over peeling?

Because wood absorbs moisture from rain and snow, and when the sun comes out and dries the wood out, the moisture vapor from the wood needs to be able to pass through the stain and escape. If there is too much stain, it restricts the moisture from evaporating away, so peeling can occur.

Can you spray Deckover?

Can I use an airless sprayer to apply BEHR PREMIUM ADVANCED DECKOVER Coating? Airless spray is recommended for experienced applicators only. … When spraying vertical surfaces, apply a very thin coat (one pass only per coat) and do not back brush/roll.

Can deck Correct be sprayed?

With correct tip sizes and pressure levels, virtually any coating in any viscosity range can be spray applied successfully. According to major equipment manufacturers, the quality of a job is most effected when worn spray tips are not replaced.

When can you put the second coat of paint on a deck?

If a second coat is required, wait 4 hours between applications. Depending on temperature and humidity, allow 24 – 48 hours of dry time before using your beautifully restored deck or porch.

What happens if it rains before deck stain dries?

If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. … If it rains right after you apply the stain, the stain will peel and flake off. If your stain has been drying for close to 48 hours, this may not happen.

Can you stain over Deckover?

Deck stains will not cover deck paint. To stain over a painted deck, you will first have to remove any current paint from your deck, either by using a deck stripper or by sanding the surfaces of your deck boards. Once the paint has been removed, you can then stain the deck.

Can I apply a second coat of deck stain a week later?

Yes you cannot apply now but you can apply a light coat after a light cleaning 6-12 months later. It is normal that you have to redo every 2 years and other semi-transparent brands will not last any longer. They all fade.

How long does deck paint last?

The pros of painting your deck include: It’s fairly easy to maintain. When you opt to paint your deck, you won’t have to refinish it anytime soon. A quality paint job, finished by a trusted professional, can last for ten years before needing repainting.

How long do I need to wait after washing my deck to stain it?

Always make sure the deck is clean and dry before you begin staining. Wait at least 24 hours after washing your deck to apply stain. Also, try to avoid staining your deck right before it rains. Most stains require at least 2-3 hours for drying.

Is Cabot deck correct a good product?

5.0 out of 5 stars Very Durable, good looking. I applied this to a deck that was horribly neglected… dried, cracked boards, with lots of mildew. I put a lot of work into prepping the deck – scrubbed and pressure washed it with bleach/detergent, then went over it with a sander.

Do deck restorers work?

You can restore your existing deck by applying a deck paint restoration product. Deck paint restoration coatings are thick enough to fill all cracks, knotholes, and splinters, and they provide a completely new textured surface that can last as long as 13 years without additional applications.

Can you use deck correct over paint?

Cabot DeckCorrect needs to be applied in two coats, and it has a relatively thick consistency. A double layer of thick stain isn’t the ideal surface to apply paint over. … You can use Cabot’s Problem Solver Wood Stripper or Problem Solver Wood Cleaner to prep the area before applying your primer and paint.

How long does Behr deck stain need to dry before rain?

Must apply between 35-90˚ F and temperature must stay above 35˚ F for the next 12 hours. Avoid applying in direct sunlight or to hot surfaces. Coating will resist rain after 4 hours. The surface must be completely dry before application.

How do you prep a deck for painting?

Applying a deck wash product to completely clean all wood surfaces. Allow to dry thoroughly, at least 48 hours. Sanding any ridges or lifted grain with 80-grit sandpaper; cleaning up any dust. Protecting adjacent surfaces, such as siding, with painter’s tape and plastic sheeting.