Hang your first patio light string with the male plug closest to your outlet. Use zip ties or hooks between each bulb as needed on deck railings or other structures. If applicable, attach the strings to your guy wire as you go.

What hooks do you use to hang patio lights?

One of the ways to hang outdoor patio lights without nails is using adhesive hooks or gutter hooks. Alternatively, you can tape or staple them to your wall.

How do you hang lights under a covered patio?

Use a staple gun loaded with 1⁄4 in (0.64 cm) staples to secure the cord to your patio cover. If you want your lights to have a tight, cinched-down look, place a staple at the midpoint between every bulb. If you’d prefer them to hang down a little looser, try spacing out your staples every 2-3 bulbs.

How do you hang outdoor string lights?

1. Step 1: Measure & Prep. The first thing to do is measure for both your string lights and the cable guide wire you need for spanning across any open spaces. …
2. Step 2: Mount Screw Hooks. …
3. Step 3: Connect & Tighten Cable. …
4. Step 4: Attach Your String Lights. …
5. Step 5: Sit Back and Enjoy!

How do you hang outdoor lights on concrete?

If you prefer, put concrete around the post almost to the top of the container. Let it dry and cure. Then sit small, potted plants on top of the concrete. Use a ladder to drape the lights over the hooks at the top of the posts or attach them to the hooks with twist ties.

How do you hang lights on a patio ceiling?

1. Step 1: Select Anchor Points. Lay string lights around the perimeter of your deck. …
2. Step 2: Install Screw Eyes. Predrill holes into the wood structural supports in your marked locations. …
3. Step 3: Attach String Lights with Carabiners. …
4. Step 4: Install Light Bulbs. …
5. Step 5: Attach String Lights to Power.

How do you hang patio lights without stucco?

Use Adhesive-Backed Hooks Just like with gutter hooks, adhesive-backed hooks can help you hang outdoor lights without using nails or drilling holes. However, you don’t hang these off the lip of a gutter or other surface. Instead, you either peel the back or apply adhesive to the hook and pin it onto a flat surface.

How do you hang string lights without holes?

Using Hooks If you can’t repurpose your backyard to hang the lights, then the next best option is to go with adhesive hooks. They can be bought at any hardware store and allow you to hang lights without leaving nail holes in your walls.

How do you hang outdoor lights on stucco?

How do you hang string lights on stucco? You could use hot glue or double-sided tape to attach the string lights. Add a small bead of glue onto the back of the lights and stick them individually to the wall. Hold them against the wall for 10 seconds so the glue dries and they stick.

How do you hang string lights outside without trees?

1. Hanging Lights on 4X4 Posts.
2. Using Metal Pole and PVC. …
3. Along the Fence Lighting.
4. Deck Lighting.
5. Gazebo or Pergola or Covered Patio String Lights.
6. String Lights on Umbrella.
7. Use Planters to String Backyard Lights.

Article first time published on

How do you hang patio lights on a deck?

1. Clean design. Initially, I had wanted the lights to be angled from one corner to the next. …
2. Measure Your Space. …
3. Anchor Ports. …
4. Use hooks and silicone. …
5. Keep the lights away from the wall.

How do you hang patio lights on siding?

To attach them to the hooks, I just used an old wire coat hanger to loop through the screw holes in my boxes, twist, and hang them up. The little hooks made it really easy to string our outdoor lights to the corner of our house too. The only bummer is the hooks only work if you have vinyl siding that can be separated.

Can you nail into stucco?

The short answer to this question is… yes you can nail through stucco using a hardened nail, like a masonry or concrete nail. Pre-drilling a hole first though, using a masonry/concrete bit will make nailing the nail a lot easier, reduce possible cracking and you can use just about any nail at that point too.

Can you staple outdoor lights?

Flip the power source’s light switch to test them to make sure they work. Turn the light switch off. Leave a little slack at the area closest to the power source and use a staple gun with ¼-in. staples to attach the string lights closest to the power source.

Can you hang string lights with a staple gun?

Using a staple gun to attach holiday lights is an action that will get you on the naughty list. … Not only will staples damage your home, you could also damage the lights. One staple misfire can ruin an entire strand of lights. So, the first rule for safe decorating: Put down the staple gun.

How do you hang something on stucco without damaging it?

To attach lightweight items, use special adhesive hooks for stucco. Adhesive hooks stick to the wall right away, and once you are done with their use, you can even remove them in a jiffy. Adhesive strips or hooks will stick to most smooth surfaces, but may not be suitable for textured surfaces.

What kind of anchor do you use for stucco?

The best type of wall anchor to install in stucco is an all-purpose anchor that spreads wide for hollow areas but only thickens for solid areas.

How do you hang lights without tape or nails?

1. Drawing Pins. …
2. Blu-Tack. …
3. Wrapping around household objects. …
4. Wire Suckers. …
5. Damage-free Adhesive Hooks.

How do you hang strings with Command hooks?

To attach the Command™ Outdoor Light Clips, remove the blue liner and press the adhesive strip firmly to the back of the clip. Then, remove the black “wall side” liner and press the clip to window. Press firmly along the entire clip for 30 seconds and wait one hour before use.

How do you hang LED lights on a deck?

1. Determine how many poles you will need. We used two – one on each of the farthest corners of the deck. …
2. Paint or stain the wood poles to match the deck. Allow to dry.
3. Attach poles to the deck. Using wood screws, attach each pole to the back of the deck. …
4. Add hooks. …
5. Attach string lights.

How can I hang Christmas lights without clips?

Purchase S-shaped gutter hooks at the home improvement store, and hang them up by pressing the top part of the S into the gutter, with the rest of the hook resting on the front. When you’re ready to hang the lights, simply use the bottom part of the S as a hook and string the wire of the lights into each hook.