Plastic toys from the dollar store or thrift shop are great pieces to start with. The plastic is softer and very forgiving if you end up needing to take a few tries to get the hole drilled out. They are somewhat large for your basic door knob or drawer pull, but could work on the right piece.

What can I use instead of drawer pulls?

Plastic toys from the dollar store or thrift shop are great pieces to start with. The plastic is softer and very forgiving if you end up needing to take a few tries to get the hole drilled out. They are somewhat large for your basic door knob or drawer pull, but could work on the right piece.

How do you put pulls on a shaker drawer?

Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.

How do you measure for drawer pulls?

The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.

How long should drawer pulls be?

Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.

What are standard drawer pull sizes?

For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another).

Are all drawer pulls the same size?

Consistent Size Throughout There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably.

How do you center handles on drawers?

Move the ruler across the drawer front diagonally in the other direction, from top right corner to bottom left corner. Trace the inner line of the ruler. Where the two lines intersect is the center point of the drawer, centered horizontally and vertically.

What size are drawer pull screws?

Standard #8-32 machine screw, used for drawer front knobs and pulls. Different length screws used for installing pulls and knobs.

How do you install cabinet pulls evenly?

Most drawer pulls are centered on the drawer fronts, but if the cabinet you’re working on has two or three drawers the same size and one larger one at the bottom, install the bottom knob (or pull) higher than the center of that drawer front. Install it so all the knobs on the cabinet are spaced evenly.

Article first time published on

Can you mix knobs and pulls in a kitchen?

Yes. You can mix knobs and pulls. It’s recommended to use pulls for cabinets that are higher up and knobs for lower style cabinets. Lower drawers that slide are typically fitted with a pull handle.

Where does hardware go on Shaker cabinets?

For 5-piece cabinets (like a Shaker or any style that isn’t one flat slab of wood), the traditional placement is to center the knob in the corner of the face frame, so that the knob is in the center of both the vertical and horizontal frame pieces.

Where do cabinet door pulls go?

For both upper and lower cabinets, the pulls should be installed vertically 2 ½ – 3 inches in from the corner of the door. For drawers, they should be installed horizontally in the center of the door. While there is no hard-set rule for the size of your pulls, consider using longer ones on larger drawers and cabinets.

Where should cabinet knobs be placed?

Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.

What size drill bit do you use for cabinet knobs?

Drill Holes Most cabinet screws need a 3/16-inch diameter hole, so use a power drill with a 3/16-inch twist bit to create the screw holes. The cabinet pull manufacturer’s instructions will specify the required drill bit size as well.

What size screw is used for cabinet knobs?

Standard #8-32 threading is common for the majority of cabinet knobs and pulls.

Can you mix drawer pull sizes?

There’s no “rule”, it’s a matter of looking at as many kitchens as possible and figuring out the look you prefer. I also used a variety of sized pulls on drawers of different widths, and used Restoration Hardware.

Do you put drawer pulls on fake drawers?

I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.

Should drawer pulls be centered?

Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.

How do you make acrylic drawer pulls?

1. Step 1: Cut your acrylic to length. …
2. Step 2: Taper the ends of your rod to fit into the mounting brackets. …
3. Step 3: Glue the mounting brackets to the acrylic rod. …
4. Step 4: Paint. …
5. Step 5: Let paint dry, remove tape, and install.