To determine the best flange size for you, you’ll need to measure your nipple. Take a tape measure or ruler and measure the diameter, or width across, of your nipple in millimeters. Do not include measurements for your areola, the larger part around your nipple. Select your flange size based on your measurement.

How is a flange measured?

To determine the best flange size for you, you’ll need to measure your nipple. Take a tape measure or ruler and measure the diameter, or width across, of your nipple in millimeters. Do not include measurements for your areola, the larger part around your nipple. Select your flange size based on your measurement.

What is the difference between blank flange and blind flange?

RE: What is the difference between a blind flange and a flange blank? A blind flange dead ends the tubing flow; a blank flange is one that is to be machined to a finished product. Or,it is that can not see and the other has no facial expression.

What is a flange blank?

Blank flange are used to seal the end of a pipe line or fitting. CRP blank flanges have a PTFE disc of raised face dimension bonded onto a steel blank flange or if the blank flange is used with antistatic piping it is supplied with a moulded antistatic PFA raised face.

What is a blank in piping?

What is a line blank? A line blank can be viewed as an “isolation flange” inserted between two mating flanges to switch on or off the piping system after disassembling certain flange bolting.

How do I know what flange I have?

You need to find the outer diameter, the inner diameter, the number of bolt holes, bolt hole diameter, and the bolt circle diameter. Bolt circle diameter (B.C.) is one of the most important measurements to make when identifying a flange.

What is flange size?

The size of the flange you need is the size of your nipple. You can measure yours using a ruler or measuring tape. Be sure to measure the diameter of the nipple alone—do not include the areola. When you get your pump, you can tell that the flange is a proper fit if: You are not experiencing pain in your nipple.

How do you use a spectacle blind flange?

Spectacle Blinds are simple safety devices that are installed between two pipe flanges. During normal operation, the open end is installed as a spacer to allow uninterrupted flow. To stop the flow in the pipeline, the blind end is rotated into place between the flanges.

What does a blind flange look like?

A blind flange is a solid flange as shown below. … Blind flanges, just like standard pipe flanges, can be raised face (RF) or flat faced (FF). If the flange is RF we would recommend a standard ring gasket that is appropriate for the service and/or test.

How many types of flange are there?

Flange types 5 are.. Welding Neck, Slip On, Socket Weld, Lap Joint, Threaded and Blind flange. Below you will find a short description and definition of each type, completed with an detailed image.

Article first time published on

What is puddle flange?

What is Puddle Flange ? It is a unit through which the water or any liquids passes through the walls while protecting the walls from seepage of the liquid. Puddle flange is extensively used in plumbing and water treatment systems.

What is a spectacle flange?

A spectacle flange is a specialty flange made of two metal discs attached in the middle by a small section of steel. Spectable flanges get their name because they look like a pair of reading glasses, or spectacles. … One end of the spectacle flange is solid, while the other end has a hole in the center.

What is a line blank used for?

Line blanks are intended for use between flange connections in pipelines and on vessel connectors.

What is spacer and blank?

Spectacle blind, spades, and spacers are also known as figure-8, paddle blank, Slip blind, and spacer. These are three different components that used in piping for positive isolation of the section of a line or equipment during maintenance and shutdown.

What is spacer in piping?

Spacer Rings, also known as piping spacers, are used between flanges to correct gaps or misalignment. Spacer rings are sometimes tapered and are almost always custom machined per very specific measurements.

How do I know if my flange is too small?

How Can You Tell if Your Flange is Too Small? Flanges that are too small may cause excess friction, pinching, or squeezing as the nipple is pulled against it. As a result, your nipple or areola could become white or discolored, and you could experience low milk supply or painful milk extraction.

What happens if your flange is too big?

If your breast pump flange is too big you may experience: Your areola could become pulled into the flange and tunnel. Painful nipple pinching, pulling, and squeezing. Lower breast milk production. Your nipple or areola could become white or discolored.

What size flange should I use when pumping?

If your nipple measures 16 mm in diameter, your recommended breast shield size is 21 mm. This is because the 21 mm shield fits nipples up to 17 mm in diameter. If your nipple diameter measures 24 mm, your recommended size would be 30 mm.

How can you tell the difference between Code 61 and Code 62 flanges?

The “A” dimension of the Code 61 differs from the same dimension of a Code 62 by a meager 0.064″ and the “B” dimension by a scant 0.188″. Add to this the minor change Caterpillar® makes to their flanges, and the confusion grows proportionately.

How do you specify a flange?

FLANGE SIZES The key sizes for a pipe flange are: the nominal size (i.e. the bore size of the flange, to match the bore size of the connecting pipe) the flange rating (which designates the pressure/temperature performance of the flange, i.e. 150#, 300#, 400#, up to 2500#)

What is flange fitting?

A flange joint is a connection of pipes, where the connecting pieces have flanges by which the parts are bolted together. Although the word ‘flange’ generally refers to the actual raised rim or lip of a fitting, many flanged plumbing fittings are themselves known as flanges.

How do you measure the thickness of a blind flange?

Re: Calculation of blind flange thickness The equation of calculating the thickness of blind flange as derived from ASME code, Section VIII, Div. 1, is: T = d [C P/S E + 1.9 W hG/S E d3]0.5 , for nomenclature see UG-34(c)(2) and Fig. UG-34 Sketch (j).

Is blind flange a termination flange?

Blind flanges may be used when testing pipe pressure, to create an access point in a piping system, to temporarily seal a piping system while modifying or repairing the line, or to create a long-term seal to terminate a piping system. A blind flange is bolted, rather than welded in place.

What are blind flanges made of?

A blind flange is a solid steel piece with no bore (interior diameter) and primarily designed to cap off a line.

What is slip on flange?

Slip on flanges are a popular type of pipe flange designed to accept pipe into the bore/center of the flange for welding around both the Outer Diameter (OD) of the pipe and on the interior side of the connection. … This flange type is extremely common in lower pressure applications.

What is the difference between spacer and spectacle blind?

Jointly they perform the same function as a Spectacle Blind as essentially a simplistic valve. The Spade or Spacer is fitted in the line between two flanges and is bolted in place. The Spacer is used when the line is required open and the Paddle Blind or Spade is installed when the line is required blocked or closed.

What is the use of jack screw flange?

This jack screw is used to facilitate separating the flanges for inspection or replacement of the Orifice Plate and gaskets. The range of orifice flanges covers all standard sizes and ranges, and all common flange materials.

What is RF in flange?

The raised face (RF) is the most common type of flange facing used. It is called a raised face flange because it has a raised surface above the bolting circle where the gasket is placed. These flanges are widely used in oil and gas pipelines. They are appropriate for both high and low temperatures and pressures.

How do you connect a pipe to a flange?

Typically flanges are welded or threaded, and two flanges are connected together by bolting them with gaskets to provide a seal that provides easy access to the piping system. These Flanges are available in various types such as slip on flanges, weld neck flanges, blind flanges, and socket weld flanges, etc.

Which type of flange is used in high pressure services?

Ring Joint Face (RTJ): Used in high-pressure and high-temperature processes, this face type features a groove in which a metal gasket sits to maintain the seal. Tongue and Groove (T&G): These flanges feature matching grooves and raised sections.

Do you need a puddle flange on concrete?

You do need a puddle flange on a concrete slab or wall if there is a pipe passing through it. This would be the case with pretty much every bathroom that has sewer pipes. … The flexible ones can also be used in bathrooms, but have to be installed inside the bathroom concrete slab.