Any plumbing professional can tell you that the standard is a 12” rough-in, and this is true for both two-piece and one-piece toilets. You will find sometimes find a 10” or a 14” rough-in measurement. If it’s not one of those three lengths, then you have a truly unique situation.

What is the rough in plumbing for a toilet?

Any plumbing professional can tell you that the standard is a 12” rough-in, and this is true for both two-piece and one-piece toilets. You will find sometimes find a 10” or a 14” rough-in measurement. If it’s not one of those three lengths, then you have a truly unique situation.

Can you install a toilet yourself?

All you need are a few hours, a helper and the right tools and toilet parts for the job. Before you begin learning how to install a toilet, choose your new toilet and, if you aren’t replacing an existing toilet, make sure you have plumbing ready for the new installation.

Does every toilet need a vent pipe?

And the answer is yes, your toilet has to have a vent. For more information on the great importance of plumbing vents, read our plumbing vent article here. And the size of this vent pipe depends on your local plumbing code. … Your toilet’s individual vent needs to be 2”.

What happens if a toilet is not vented?

Poorly-vented drain lines will not be able to effectively move wastewater and solid waste out of your building. This could lead to problems such as overflowing drains, backed-up toilets, and similar plumbing issues.

Does toilet flange go inside pipe?

Buy an inside closet flange. This toilet flange is designed to glue on the inside of the pipe or expand inside the pipe. … The flange should be sitting with the bottom edge flush with the top of the floor. If it isn’t, then you will have to cut away the old flange.

Do you install toilet flange before tile?

5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.

Can I move a toilet a few inches?

Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side. This will allow you to use the same wastewater line and in turn help to save you a lot of money.

Does toilet flange need to be screwed to floor?

The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn’t rock. If it does rock, use shims to prevent rocking – just tightening the bolts probably will not stop the rocking but will risk cracking the toilet or breaking the flange.

How far should a toilet be from the back wall?

The Distance To Set The Toilet Flange From The Back Wall. You’ll want to set the center of the water closet flange 12 inches from the finished back wall.

Article first time published on

Is there a ventless toilet?

What is a ventless toilet and how does it work? Ventless toilets are just like regular ones, except there is no vent for the toilet to release the water vapor. Instead, they use a siphon action that pulls the water out of the toilet bowl into an underground waste pipe.

How do you vent a toilet without a vent?

Don’t worry if you do not have a vent pipe in your house, or if it is blocked and you can’t fix it. Instead of thinking about massive construction projects, you can use an Air Admittance Valve, well-known as a cheater vent. You may have heard that they are illegal and unreliable, but you shouldn’t believe every rumor.

How long after a new toilet is installed can you use it?

It can be used as soon as the water supply is turned on. Toilets are bolted to the floor flange, so there is nothing to dry or cure. About 30 seconds after the water is turned in. The time it takes to fill the tank.

How hard is it to install toilet?

Replacing a toilet is a major project, but it is not as difficult as might be imagined. The hardest tasks usually are selecting a new toilet and removing the old one. … Then remove the tank cover, flush the toilet and sponge the tank dry. Use a plumber`s plunger to force as much water as possible out of the bowl.

How much should it cost to have a new toilet installed?

On average, a standard toilet installation costs between $120 and $230 with most homeowners spending around $150 to $180. This does not include the price of the toilet which averages $100 to $200 for a total toilet replacement cost of $221 to $427.

How do you vent a bathroom with no outside access?

1. Install a recirculating fan in a half-bath. This type of bath fan doesn’t exhaust air to the exterior. …
2. Reduce noise with an inline fan. …
3. Vent under the floor to get outside. …
4. Build a soffit to hide ductwork. …
5. Install commercial ductwork.

Where should a plumbing vent be located?

Vent pipes must be installed so they stay dry. This means that they should emerge from the top of the drainpipe, either straight vertically or at no less than a 45-degree angle from horizontal, so that water cannot back up into them.

Can a plumbing vent go down?

Re: Can a plumbing vent go down? as far as i’m concerned, yes. as long as any condensation can drip somewhere, there should be no problem. we run island vents for kitchen/bar sinks all the time.

Should I put the wax ring on the toilet or the flange?

Place the wax ring on the closet flange, not on the toilet. Pick up the toilet and set it evenly over the closet flange, making sure the bolts come through the bolt holes in the toilet base. Fine-tune the toilet position, so it’s right where you want it, then push it straight down so it smashes the wax evenly.

Should you tile behind a toilet?

The bathroom fitters are unanimous—if you’re looking for a high quality finish, with a better seal against water damage, then always tile the floor first. … It is also easier to do this rather than trying to cut tiles around the toilet.

Do you need to caulk around a toilet?

Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It’s actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?

Are toilet flanges glued?

In addition to being glued to the waste pipe, toilet flanges are typically attached to the bathroom subfloor with screws. Often, there are four screws that attach the flange to the subfloor.

How do I know what size toilet flange I need?

The most common and readily available toilet flange is the 4 x 3-inch size. This pipe is 4 inches wide at the top but only 3 inches wide at the bottom. The 3-inch bottom is the correct size for fitting the schedule 40 pipe most frequently used in home drains.

Can you put a new toilet flange over an old one?

Either slide the new closet flange bolts into the old flange before adding the extender or add them after you adhere the extender to the old flange. Consequently, we chose to add one of the bolts to the old flange first since it was a tight fit. Add metal washers and nuts to the closet flange bolts.

Why does my toilet rock when I sit?

Toilets usually rock because they are not resting flush against the floor. Underneath the toilet base is a round toilet flange that connects the toilet to the drain pipe. If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side.

When should I use toilet flange spacer?

You need a flange extender when the existing flange is too low to hold the wax ring in the correct place to meet the bottom of the toilet drain.

How much does a plumber charge to replace a toilet flange?

The cost for a plumber to replace the toilet flange varies by region and service provider, but the average price range is approximately $130 to $310.

What size is a plumbing vent pipe?

Vent pipes shall not be less than 11/4 inches (32 mm) in diameter. Vents exceeding 40 feet (12 192 mm) in developed length shall be increased by one nominal pipe size for the entire developed length of the vent pipe.

Does a soil pipe have to be vented?

Soil vent pipes are a critical part of any drainage system. Without a vented pipe, a vacuum would build up behind the waste water as it moves down the pipe. This would force the water out of u-bends, in turn allowing foul odours and gases to enter the property.

Is it expensive to relocate a toilet?

The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move. Connecting the toilet to the existing sewer line can be a bit tricky for your plumber.

What is a toilet ring?

Your toilet’s wax ring creates an airtight seal to prevent water and sewer gas from escaping. When the thick wax ring goes bad, you need to replace it right away to prevent leaks.