Press and hold the SET button (a little circle button on the inside of the interior assembly; see the image above). Keep holding the SET button. Next, put the battery back in and then release the SET button. The green LED indicator will illuminate, followed by two beeps and that shows the lock is reset.

How do you unlock a gatehouse lock?

Locking from inside: Turn the interior thumb turn to a horizontal position to lock the door. Unlocking from outside: Enter an existing user code to unlock the door. Unlocking from inside: Turn the interior thumb turn to a vertical position to unlock the door.

Can Gatehouse locks be rekeyed?

Rekey Kit For 5-pin Gatehouse Door Locks You will be able to rekey up to 10 lock cylinders with a new key code. You will need your old key to assist you in the rekey process.

How do you change the code on an electric door lock?

First, open the door and lift off the lock’s interior cover. Press the Program button once and you should hear your unit beep five times and see its checkmark icon at the keypad’s bottom left flash five times. Press the checkmark once and then enter the master code.

How do you reprogram a door keypad?

1. Enter your 6-digit default programming code.
2. Press the Schlage button and key 3. This will trigger three beeps and flashes.
3. Now enter your new 6-digit programming code after the flashes and beeps.
4. Wait to see if the light turns green. If it does, then your new code is successfully entered.

Where is Schlage program code?

The default programming code is printed on a label on the programming guide that came with your lock. If you do not have access to the guide, remove the lock from the door and look on the back of the lock for a label containing the default code.

Can you rekey a lock yourself?

When you rekey a lock by yourself, you will need to purchase a rekey kit that is specific to your brand of doorknob, lever, or deadbolt. … In most cases, all other pieces of the lock stay the same. A few simple tools are usually included with the kit.

Who makes gatehouse door locks?

“Who makes Gatehouse locks?” is a question we often get asked. And, the answer is simple- Lowes.

How do I reset my Schlage keypad lock without the code?

1. Disconnect the batteries.
2. Press and hold the Outside Schlage Button.
3. While holding the Outside Schlage Button, Reconnect the batteries.
4. Release the Outside Schlage Button.
5. To check that the lock was reset, press the Outside Schlage Button and enter one of the Default User.

Is it cheaper to rekey or replace locks?

Rekeying your lock is almost always cheaper than replacing a lock. This is because of the cheaper price of the key pins inside the locks, whereas when you replace a lock, you are paying for all brand-new parts.

Article first time published on

Can Ace Hardware rekey locks?

Ace Hardware can rekey locks of the brands Schlage, Kwikset, or Ace brand. Further, Ace Hardware can rekey doorknob or deadbolt locks.

How much does it cost to rekey a lock?

How Much Does Rekeying Cost? Second, rekeying is significantly less expensive than changing your old locks for new ones. While a new keyed or keyless lock, gripset and matching interior trim runs from $130 to $360, the cost of rekeying a lock is about $80 – regardless of whether you have a keyed or keyless unit.

How do I unlock my office cabinet without a key?

1. Take one piece of wire and bend it into a “Z” shape using your pliers. …
2. Take a second piece of wire and bend it so that it has a small upward point on one end. …
3. Place one end of the torque wrench into the lock, and apply pressure with your thumb.

How do you reset a Schlage Lock?

Reset the Schlage lock by engaging the reset button if one is available, or by disconnecting the battery. Once the cover and housing are removed, if the button is there, simply press and hold it until the red light isn’t flashing anymore. Release it and wait until the lock resets itself and the light turns blue.

How do you reset a Schlage code?

Press key 6 and wait for three orange lights from the Schlage button, followed by three beeps. Now enter your Programming Code again. This will delete the two default User Codes.

How do I reset my Schlage Lock password?

Press the “Schlage” button and the number “1” button simultaneously to add/change a new entry code. Wait for the “Schlage” button to beep and flash three times. Enter a new four-digit code, and wait for the “Schlage” button to flash and beep three times. Re-enter the same four-digit code to confirm the change.

How do I change the 4 digit code on my TRU bolt lock?

1. Enter the existing Programming Code (the one you want to change) and press the Unlock button. …
2. Press key 4 and then press the Unlock button.
3. Enter a new Programming Code (6 digits) and press the Unlock button.