Staggering Shiplap Creates A Balanced Aesthetic When installing shiplap on a wall or ceiling that exceeds the length of your shiplap, you’ll need to butt boards together. Stagger the shiplap boards so that the end joints are spread out along the wall or ceiling randomly.

Do you stagger shiplap on walls?

Staggering Shiplap Creates A Balanced Aesthetic When installing shiplap on a wall or ceiling that exceeds the length of your shiplap, you’ll need to butt boards together. Stagger the shiplap boards so that the end joints are spread out along the wall or ceiling randomly.

Can you have too much shiplap?

As much as we love shiplap, there can be a time and a place when there is too much shiplap. When you want to fully decorate the walls with shiplap, it is best to stick with soft, neutral colors and limited texture.

Do you start shiplap from the top or bottom?

Installing The First Board By starting in the corners, you can make sure your boards are always aligned perfectly. Always install shiplap from the bottom up, it makes the installation process easier by using gravity to help hold the next board.

How do you join the ends of shiplap?

1. After all your shiplap is installed, run a bead of caulk around all seams where the shiplap terminates to a wall, or along inside corners. …
2. Fill in all your nail holes and seams between boards with wood filler and a putty knife.

Do you put baseboard over shiplap?

Keep your baseboards, and install shiplap boards that are equal to or have a shallower depth. This way, your shiplap can rest atop your baseboards and won’t stick out. Use whatever shiplap you want and ignore differences in depth where the planks meet the baseboard.

How far apart should shiplap boards be?

Spacing the Boards: Enlist spacers to create uniform gaps (typically 1/8 inch) between each board. You can use any type of spacer you’d like, such as the edge of a carpenter’s square or tile spacers. Make sure that you position each board using the same spacer so the boards appear evenly spaced.

Can you use liquid nail for shiplap?

Shiplap can be installed directly to sheet rock/drywall. Simply mark the stud locations for nailing the shiplap or you can apply a construction adhesive such as liquid nails. … Use a nail gun with 18 gauge 1 3/4”long brad nails. Nail through the top flange which is the longer of the two flanges.

What kind of trim do you use with shiplap?

There are a lot of options to cover where the tile meets shiplap. You can use any trim with a flat back for this spot. For a modern look, consider using plain trim (like lattice wood). In this bathroom, I used a more decorative trim for an added detail.

Do you screw or nail shiplap?

Nails are the best options when installing shiplap cladding. Trim nails are faster to install than screws since you do not need to predrill the material and won’t be risking causing unsightly splits. They can also be easily covered or touched up if needed.

Article first time published on

How do you stop the shiplap on an outside corner?

Depending on whether it is an inside or outside corner, you may want to finish them differently. We recommend either using corner trim or butt-jointing boards together at an angle. An unfinished corner can draw unwanted attention, so you’ll want to make sure they are finished properly without any gaps.

Do you install shiplap over drywall?

You can install shiplap right over the drywall. However—and this part is crucial—you must first take the time to find all the studs within your walls and mark them carefully before you place a single board.

Does shiplap make a room look bigger or smaller?

Horizontal shiplap looks great in a range of different interiors, but another option for installing shiplap is to install it vertically. Rather than making rooms look wider, installing shiplap vertically helps draw the eye upward, making the room appear taller.

Can you put shiplap on every wall?

Shiplap was originally used as an inexpensive exterior solution on barns and historical homes. However, because it’s so versatile and attractive, it’s now made its way into many interior spaces, too. Since shiplap is such a flexible material, it can work in almost any room in your home.

Can you put shiplap on just one wall?

The traditional version usually has grooves cut into the top and bottom (called rabbets) which allow the pieces to fit together tightly. In design, shiplap can be installed as a decorative accent in just about any room on the walls or ceiling.

How do you hide seams on shiplap?

Before plywood and drywall, builders would line rooms in shiplap to keep them warm and dry, then cover it with a layer of muslin or cheesecloth and wallpaper to hide the shiplap’s seams.

Do you have to glue shiplap?

Tip: You can attach your shiplap boards with construction adhesive or nails or both.

Do you fill nail holes in shiplap?

For primed shiplap, since you’ll be painting it, you can fill in nail holes with a wood filler. Once you sand down the nail holes you filled in, paint over for a seamless look.

Is shiplap cheaper than tongue and groove?

Shiplap is cheaper than tongue and groove, but it requires a bit more work on the carpenter to get the rows to lay flat against the building in a waterproof fashion. Also, if not installed properly, shiplap is more likely to warp and leak than its counterpart.

How high should shiplap be on wall?

Give some thought to how high you want your trim. So 1/3 or 2/3 of the wall will look better than half of a wall. It won’t be exact, but try to get close. I wanted mine to go a bit higher, but then it would have impeded with the electrical outlet, towel racks, and light switch.

What nail gun do I use for shiplap?

A finish nailer or brad nailer is the easiest and most efficient tool to use when installing your new shiplap or tongue and groove. They can be purchased/rented relatively cheaply from your local hardware store, they’re lightweight, and are simple enough that a 12 year old can use them!

Do I need to drywall before shiplap?

If don’t already have drywall installed, you do not need it as a base for affixing shiplap. You can install shiplap directly to your studs to save on time, money, and mess.

Do you have to caulk shiplap?

The edges of the shiplap wall need to be caulked (with paintable caulk) wherever there is molding and then they need to be “cut in” with the paint brush. For my wall, we caulked the gaps along the inside wall corners (where we installed quarter round molding), the floor molding, and the top crown molding.

Is shiplap going out of style?

Shiplap is falling out of fashion. Once used to waterproof boats, shiplap siding became a trendy way to decorate interior walls in the 2010s. … Street added that tile, plaster, rattan, or living walls of plants are becoming more popular this year, instead.

What does Joanna Gaines use for shiplap?

The best-rated product in Magnolia Home by Joanna Gaines Appearance Boards is the 1/4 in. x 5.1 in. x Varying Lengths Stone HDF White Oak Shiplap Wall Plank (20.3 sq. ft./Carton).

Should you paint shiplap before installing?

If you’re installing new shiplap, paint it prior to installation. It will be far easier to paint the edges before the shiplap is up on the wall. … If the shiplap was already installed, paint it like wall (with a roller and cut in with a brush), taking extra time to paint the gaps and shiplap grooves with a small brush.

What's the best construction adhesive?

• BEST OVERALL: Gorilla Heavy Duty Construction Adhesive.
• BEST FAST-DRYING: Loctite PL Premium Fast Grab Polyurethane.
• BEST HEAVY-DUTY: Liquid Nails Extreme Heavy Duty Construction Adhesive.

How do you shiplap half a wall?

1. Step 1: Cut your Boards. …
2. Step 2: Prime your Boards. …
3. Step 3: Paint your boards. …
4. Step 4: Remove the Trim & Paint it. …
5. Step 5: Attach the Horizontal 1 x 4 to your Wall. …
6. Step 6: Attach the Vertical Shiplap Boards. …
7. Step 7: Cut the Boards for the Ends as Needed. …
8. Step 8: Attach the 1×2 Board to the Top of the Half Wall.

How wide should shiplap be?

Fortunately, shiplap comes in numerous widths to best fit the interior design of your home; however, 5 ½-inch and 7 ¼ -inch are the most commonly used widths. You can use one width of shiplap board to create your home’s style, or you can mix the widths to create a unique design.

How do you caulk corners in shiplap?

1. Once you have installed your shiplap, run a bead of acrylic caulk (also known as latex caulk) along the seams where the shiplap ends butt up to a wall, inside corner or molding.
2. Smooth out the caulk with a clean finger or rag so that the caulk fits neatly into the seam.

Is shiplap 6 or 8 inches?

While shiplap can come in several different sizes, the standard width for shiplap is 6 inches. It can be as wide as 8 inches and as narrow as 4 inches. The 4 inch version is referred to by Joanna Gaines as skinnylap.