There are many reasons why a Cub Cadet lawn mower won’t start including a loose spark plug connection, plugged air filter, bad fuel pump, bad battery, corrosion on the electrical components, dirty carburetor, bad switches or a faulty charging system.

Why does my Cub Cadet not start?

There are many reasons why a Cub Cadet lawn mower won’t start including a loose spark plug connection, plugged air filter, bad fuel pump, bad battery, corrosion on the electrical components, dirty carburetor, bad switches or a faulty charging system.

How do you start a choke on a riding lawn mower?

1. Sit firmly on the seat.
2. Start the Engine.
3. Press the Brakes.
4. Engage the Parking Brake.
5. Put the Gear to Neutral.
6. Pull the Throttle onto Choke Position.
7. Insert the Ignition Key.
8. Turn the Key to the Right hand side/Clockwise.

How do you turn on a Cub Cadet blade?

To engage the blades, be sure that your throttle or choke is in the rabbit position. Then, push the PTO or blade engage lever forward into the on position.

Why is my lawn mower turning over but not starting?

The most common reason for a riding mower cranking over but not starting is bad gas, but other possible reasons include: Gas Valve Off. No Gas. Choke Fault.

Why won't my PTO engage on my Cub Cadet?

Common solutions for: Cub Cadet Lawn mower blades won’t engage. … If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it.

How do you start a Cub Cadet Series 1500?

1. Sit down on the tractor seat. …
2. Place the choke control knob in the full choke position. …
3. Slide the throttle switch halfway between “Slow” and “Fast” and turn the PTO switch to “Off.” Move the speed control lever to the “N” position and press down on the single brake pedal.

How do you start a riding lawn mower without a choke?

If the engine is not cold, do not use the choke. Position the throttle lever between the fast and slow position. Most throttles have a picture of a rabbit for fast and a picture of a turtle for slow. Insert the riding mower ignition key into the ignition switch and turn the key to the right.

Where is the PTO switch on Cub Cadet?

Find the small bell housing on the underside of the Cub Cadet’s Briggs & Stratton engine. This housing is for the PTO clutch.

What is the choke position on a lawn mower?

This choke plate reduces the amount of air and increases the amount of fuel supplied to the engine. Choke – Choke set to full to start a cold engine, after the engine warms up move the choke to the fast setting. Some mowers use a snowflake symbol for the choke.

Article first time published on

How do I know if my Cub Cadet starter is bad?

A bad starter can manifest itself in a cranking noise without engine turnover, a clicking when the ignition button is pressed, or a mower that simply does not respond to attempts to start. An indication of a bad starter motor is the absence of other electrical problems that can be more easily tested.

How do I know if my lawn mower starter solenoid is bad?

Look for the large terminal posts on the solenoid where the thick red wires connect to the solenoid. Touch the metal shaft of a screwdriver to both of the large terminals at the same time. If the engine turns over and starts, the solenoid is bad and should be replaced.

What's the spark plug gap on a Cub Cadet?

Step 4: Properly gap your new spark plugs Use a gap tool or feeler gauge to set the spark plug gap at . 030”.

Where is the spark plug on a lawn mower?

Spark plugs are typically located on the back or side of a lawn mower engine. Look for a short wire that’s about 1/4-in. -thick leading to the top of a short, cylindrical protrusion from the engine. If you’re not sure where the spark plug is, consult your owner’s manual.

What is a PTO switch on a Cub Cadet?

The PTO (or power take-off) belt is part of a pulley system that operates the blades on your riding lawn mower. It runs off the electric clutch system in your engine. … We’ll show you, step-by-step, how to do a PTO belt repair on a Cub Cadet riding lawn mower.

Why won't my riding mower blades engage?

Belt-the number one cause for your blades not to engage is that your belt is either stretched or loose causing it to slip or fall off completely. Belt could have snapped also. When you are trying to process too much grass/leaves they could pack up under your deck and push off your belt.

Why does the PTO not engage?

If the PTO clutch is not getting power, if the clutch solenoid is defective, or if the clutch is worn out, the lawn mower blades will not engage. The PTO clutch is not repairable—if the clutch is defective, you must replace it. The PTO switch provides power to the PTO clutch. … If the PTO switch is defective, replace it.

How does a PTO engage?

The PTO is engaged and disengaged using the main transmission clutch and a remote control mechanism which operates on the PTO itself. Typically, an air valve is used to engage the PTO, but a mechanical linkage, electric or hydraulic mechanism are also options.

Why does my PTO keep turning off?

@mattk ,Matt, Something as simple as a low battery/bad connection or not charging could cause this. Possibly bad seat/reversing safety switch, faulty/loose wire/plug to clutch/PTO/switch, clutch faulty. Trouble shooting/parts/manual links below may help.