How do you tune up a chainsaw

Obviously this depends to some degree on how often and how heavily you use your chainsaw but experts generally recommend you get a professional service or check-up from every few months for heavier use to at least once a year for light use.

How often should you tune up your chainsaw?

What maintenance does a chainsaw need?

Your chainsaw needs to be well oiled in order to prevent friction between the guide bar and the chain. If there’s not enough oil, the chain won’t turn as fast as it should, and the entire tool could overheat.

What is a chainsaw tune up?

When tuning up your chainsaw, look at the spark plug, carburetor, chain and air filter. … There are four major areas that you should check or tune up during the routine maintenance of your chainsaw. These are the spark plug, air filter, carburetor and chain.

Why does my chainsaw dies when I give it gas?

Because your chainsaw will idle, but dies when it is revved up to full power, it means that the filter is only partially clogged; it will allow enough fuel to the engine to run on idle, but not enough to sustain full throttle. … If the filter becomes clogged, not enough fuel will reach the engine for it to run properly.

How often should you change the spark plug in a chainsaw?

A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.

Why does my chainsaw keep bogging down?

Many chainsaw operators first notice a problem with chainsaws bogging down when they’re using the chainsaw under load, and this is usually the result of poor air circulation. This issue is caused by a clogged air filter on the chainsaw. … Wash the air filter in soapy water until the air filter comes completely clean.

Do you need to clean chainsaw after every use?

After each use, wipe the chainsaw housing clean with a damp cloth. … Check the air intake vents and clean them with a paintbrush or compressed air if necessary; it’s important to ensure that the air intake vents are working correctly as they help to prevent the engine from overheating.

Do chainsaws need tuneups?

To keep your chainsaw running well, you should clean it regularly and perform a yearly tune-up. For the cleaning and tune-up you only need a basic set of tools, including a compatible scrench, and less than an hour of time. … This is the biggest maintenance concern for chainsaws.

Do you clean chainsaw after use?

BEFORE AND AFTER EACH USE: Clean the chainsaw bar after each use by scraping out any debris inside the track. Inspect the air intake vent for debris in the slots, as this could prevent much-needed air from entering and cooling the engine.

Article first time published on

How do I keep my chainsaw maintained?

Test the Trigger. Check your throttle trigger before each use to make sure it’s operating smoothly. …
Monitor Safety Features. …
Keep a Clean Filter. …
Rotate the Bar. …
Check the Sprocket / Tighten and Sharpen the Chain. …
Spoil Your Starter. …
Tighten Any Loose Parts. …
Check Anti-Vibration Wear and Tear.

Why does my chainsaw cut out when I pull the trigger?

An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. … If the saw is stalling when you pull the throttle trigger or it doesn’t reach its full power, adjust the high-speed (H) screw.

How do you clean a chainsaw fuel filter?

Brush the air filter gently with a soft brush or wash it in warm soapy water then dry it. Do not use compressed air to clean it – compressed air can blow holes in the filter, allowing dust and debris into your carburetor.

Why does my Stihl chainsaw bog down when cutting?

The Job of the Carburetor Without the right amount of air and fuel in the piston cylinder, the 2-cycle engine in a Stihl chain saw runs inefficiently and the saw loses power. … When the saw bogs down during cutting, it’s usually the high-speed screw you need to adjust.

Why does my chainsaw rev too high?

The throttle valve (butterfly) simply cuts off the supply of combustible air/fuel and the engine stops. If this adjustment is set too high, the high idle speed will cause the centrifugal clutch to engage and the chain will run. This is a dangerous condition and should never be allowed.

What are the symptoms of a bad spark plug in a chainsaw?

Gas mileage may be reduced.
Your check engine light is on.
You may notice an inability to fully accelerate.
Your engine may start to sound rough when idling.
You may have trouble starting your vehicle.
The engine might misfire more frequently.

How do I know if my chainsaw spark plug is bad?

Black, chunky carbon buildup spanning the gap between the sparking end of the plug and the hook-shaped metal piece overhanging the end.
Dark carbon residue built up on the ends but not spanning the gap.

How do I know if my spark plugs need changing?

The car is hard to start. …
The engine misfires. …
The car gets poor fuel economy. …
Rough engine idle. …
Your car struggles to accelerate. …
The engine is really loud. …
Your ‘check engine’ light is on. …
Frequency of replacing spark plugs.

How do I change the oil in my chainsaw?

Check and replace bar and chain oil regularly to reduce friction, keep the saw from wearing out faster, and to make cutting easier. …
Set on a level surface.
Unscrew the cap and pour oil into reservoir – do not overfill.
Screw cap back on and wipe down any excess oil.

Can I use wd40 to clean chainsaw?

Lubricating the Chainsaw’s Chain Using WD-40 WD-40 works great for both – rust prevention and lubrication. Other than this, it will also prevent some future contaminants that are inevitable after every use. So there you have it fellow lumberjacks. Your chainsaw is well oiled and sharpened for your next project.

Can you hose down a chainsaw?

After it is soaked, pull out the chain with a hooked tool of some kind, DO NOT use your hands to remove the chain from the solution even if you are wearing gloves. Throw it on the ground outside, let all the excess solution run off and hose it down thoroughly with water.

Can I use wd40 on chainsaw?

We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.

What is the best cleaner for chainsaws?

In a well-ventilated area, take a bucket and mix one cup of ammonia with one gallon of water. Place the chainsaw chain in this solution and let it soak for 15 minutes. Put on a pair of thick rubber gloves for protection. Then, use a soft-bristled toothbrush to scrub each section of the chain until it’s free of debris.

Can you use the tip of a chainsaw?

This is generally the safest way to cut. The most dangerous is to use the tip, which can see the chain’s rotation sending the business end of the saw upwards and directly at your mug.

Should I soak chainsaw chain in oil?

When it’s time to replace the chain, break it in first by soaking it in bar and chain oil for a couple hours. This ensures all the pivot points are well lubricated. Then, hang the chain from a nail and let the excess oil drip back into the pan.

How do I keep my chainsaw sharp?

Periodically filing depth gauges is one of the little-known tricks to maintaining saw-chain performance. To handle homestead chores, choose a chainsaw with a bigger bite. A larger chain cuts more aggressively. Consistency is the key to a sharp saw: File each cutter with the same number of strokes.

Why does my chainsaw stop running when it gets hot?

When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.

The Daily Insight