This tool works for plastic and brass cartridges; and is compatible with Moen 1222, 1225, and 80933. Installing a new cartridge eliminates a leaky faucet and saves both water and energy. The Danco Cartridge Puller will help make your DIY installation easier in your sink, bathroom or tub faucet.

What does a cartridge puller do?

This tool works for plastic and brass cartridges; and is compatible with Moen 1222, 1225, and 80933. Installing a new cartridge eliminates a leaky faucet and saves both water and energy. The Danco Cartridge Puller will help make your DIY installation easier in your sink, bathroom or tub faucet.

How do you remove a Moen retainer cartridge?

To remove the cartridge from your faucet assembly, first use a flat-headed screwdriver to carefully pry the cover from the handles. Using a Philips screwdriver, unscrew the handle screws and pull the handles off from the faucet assembly. Then, loosen and remove the nut from the cartridge using pliers.

How do you remove a stuck Moen faucet handle?

If it’s stuck, wrap a rag around it, give it a few light taps with a hammer and try again. Squirt a few drops of penetrating oil or spray lubricant into the space between the handle and the valve stem. Wait a few minutes, then tap the handle and try pulling it off.

How do you remove a Moen faucet handle without screws?

1. Step 1: Turn off the water. …
2. Step 2: Remove the cap on top of your faucet. …
3. Step 3: Remove the hidden set crew. …
4. Step 4: Remove the faucet handle. …
5. Step 5: Rinse off mineral deposits.

How do I change a Moen cartridge?

Use pliers on the white plastic tool and loosen the cartridge by twisting 1/4 turn each direction one at a time. After removing the white plastic tool, grasp the cartridge stem and pull it straight out of the valve (using pliers or an adjustable wrench). You can now install your new cartridge.

What is a core puller?

Core puller is an equipment that is used to pull the core sample obtained during geotechnical investigation for the purpose of studying soil property. Core samples are very important for sampling and conducting soil investigation in order to select appropriate boring methods for laying pipelines.

What is the difference between Moen 1222 and 1222B?

There is absolutely NO difference between the Moen 1222 vs 1222B replacement cartridges. They are both the replacement part cartridge for the Posi Temp Moen shower valve. They are made from the same parts, the only difference is their packaging and model number. The “B” in the 1222B model number stands for Bulk.

What size Allen wrench does Moen use?

For the most part, Moen uses hardware that will require a 7/64 inch hex wrench. This applies to Moen Renzo faucets, handle set screws on one-handle kitchen faucets, and PosiTemp levers in Moen showers.

What is the difference between Moen 1200 and 1225?

Moen 1200 has an all-round brass design which ensures longevity in the long run. But in terms of performance, Moen 1225 can offer you better performance with its 1GPM water discharge rate. While Moen 1200 does not support Posi-Temp shower valves, Moen 1225 is compatible with almost any faucet.

Article first time published on

How do you remove a faucet handle without visible screws?

Locate & Remove The Button Or Cap See if you can locate one on the top or side of the handle. If you find one, you can use a flathead screwdriver to remove it. Simply work it into the gap around the button or cap and work it around the button or cap, gently lifting as you go.

How do you remove a single faucet handle?

1. Using a bladed screwdriver, gently pry off the plug button under the handle, taking care to protect all finished surfaces.
2. Using a 1/8″ hex wrench, loosen the setscrew securing the handle to the valve stem.
3. Lift off the handle.
4. Unthread the bonnet to expose the valve.

How do I stop my Moen kitchen faucet from dripping?

1. Prepare Your Tools.
2. Turn Off Water Source. …
3. Open Up the Faucet. …
4. Reveal the O-Ring and Cartridge Tube. …
5. Determine Location of the O-Rings. …
6. Remove the Escutcheon or Crown. …
7. Pull Out the Water Spout. …
8. Take the O-Rings and Bearings Off.