EASY TO USE: With electronic self-leveling, you press the power button and go right to work in seconds. If the RL-H5B gets disturbed on the job it relevels itself automatically. The self-leveling motors are accurate to ±20 arc seconds.

How do you use Topcon RL H5B?

EASY TO USE: With electronic self-leveling, you press the power button and go right to work in seconds. If the RL-H5B gets disturbed on the job it relevels itself automatically. The self-leveling motors are accurate to ±20 arc seconds.

How do you adjust a laser level?

Start as before with the laser level facing a wall at least 20 feet away. Tape a piece of paper to the wall and mark where the line is shining. A straightedge or ruler might be useful to make it totally straight. Next, rotate the laser level 180 degrees and shine the light on the same spot.

How do you use a laser level for drainage?

1. Set up the laser level on a tripod on firm dry ground. …
2. Turn on the laser level and give it a moment to self-level.
3. Identify the initial height of your grade. …
4. Place the bottom of the leveling rod at the desired height.
5. Adjust the laser detector up or down until you hear a beep.

How do you calibrate a Topcon RL H3C?

The Topcon RL-H3C is now in calibration mode, to select the “X” axis press the “TILT” button (left button) and the “ON” light will go solid. Press the “MANU” or “Power” buttons to shift the beam up or down to align with your level mark. You can press and hold either of the buttons to move the laser’s height faster.

How do you use laser level posts?

1. Place a tripod at the end of your intended fence line. …
2. Attach a laser onto the tripod in its vertical position. …
3. Verify the laser’s attachment to the tripod by hand-tightening the threaded bell assembly. …
4. Turn the laser on using the corresponding buttons.

What are 2 things you should do before you use a laser level?

Before you can use a laser level, you need to connect a compatible battery to the device according to the instructions that came with it. Then, you need to determine where you want to place the laser level tripod, and make sure the ground is dry so it doesn’t move away from the desired position.

How do you check the accuracy of a laser level?

The principle of checking a laser level against itself is pretty much the same as checking a spirit level. With a spirit level you place it on a surface and look at the position of the bubble. You then rotate the spirit level 180 degrees on the same surface and look at the bubble position again.

How do you use a laser level without a tripod?

If you don’t have a tripod, you can place your laser level on a level surface that’s opposite the wall on which you’re projecting your level line. If your laser level comes with a leveling base, you don’t need a level surface for your laser level.

How often do you calibrate laser level?

Make sure you purchase a laser level that has had a pre-sale calibration and accuracy check like all IMEX lasers. If used daily, i.e.: concreter or tile, the laser unit should be recalibrated every 6 months, if used once or twice a week, 12 months or even 24 months is acceptable.

Article first time published on

How do you calibrate a self leveling laser level?

1. Step 1 – Set-Up All Equipment. Check out rotary laser levels on Amazon. …
2. Step 2 – Manipulate the Laser. Turn the laser towards the target (wall or pole). …
3. Step 3 – Turn on the Device. Turn on the laser. …
4. Step 4 – Repeat at 180° …
5. Step 5 – Rotate at 90º

Where is Topcon laser made?

The series is covered by the five-year guarantee on Topcon manufactured lasers. For more information, visit topconpositioning.com. Topcon Positioning Group is headquartered in Livermore, California, U.S. (topconpositioning.com). Its European head office is in Capelle a/d IJssel, the Netherlands.

How do you calibrate a Dewalt laser?

Calibration is achieved by re-weighting the pendulum usually with the use of two grub screws, one for each axis of movement, X and Y. The majority of laser levels of this type often have easy access to these two grub screws, making calibration pretty straight forward.

What are the main dangers of laser levels?

Exposure to high level lasers may cause depigmentation, severe burns and possible damage to underlying organs. High-powered lasers may also cause fire hazards.

What is the best laser level on the market?

• BEST OVERALL: DEWALT Line Laser Self-Leveling, Red, 3-Beam (DW089K)
• BEST BUDGET: BLACK+DECKER Line Laser with Stud Finder (BDL190S)
• UPGRADE PICK: Bosch GLL3-330CG 360-Degree Green Beam Laser.
• BEST FOR LIGHT-DUTY: SKIL 360° Red Cross Line Laser Level – LL932201.
• BEST FOR HEAVY-DUTY: Klein Tools 93LCLS Laser Level.

How do you find high point floors?

Find the highest point in the floor by drawing or snapping a level chalk line along the adjacent wall, then measure down to the floor in several places. The spot where you measure the shortest distance is where the floor is highest.

Can you use a laser level to level ground?

If you’re using the laser level to level the ground, or you’re an excavator and need to level the sub-grade in a foundation, the first thing you do is find a spot to set the tripod and laser level that’s nearby but out of the way. … As you can see in the picture, I’m checking the sub-grade inside this house foundation.

Can you use a laser level upside down?

Answer: Thanks for your question, if laser level sit on the tripod then it can work upside down about 1/3, but if no tripod thats can not work upside down.