Unroll the chicken wire a few inches and slip the horizontal wires along the first or second column of chicken wire cells into the tabs on a metal T-post and pinch them closed with pliers — or staple across each horizontal wire down the first column of cells to fasten the wire to a wooden post.

How do I attach wire to wooden post?

Unroll the chicken wire a few inches and slip the horizontal wires along the first or second column of chicken wire cells into the tabs on a metal T-post and pinch them closed with pliers — or staple across each horizontal wire down the first column of cells to fasten the wire to a wooden post.

Does fence go on inside or outside of posts?

Fence posts should be on the outside of the fence The correct installation of ag fencing is to place it on the inside of the posts. This way, animals in the enclosure brush against the wire, not the posts.

How do you attach wire mesh to a fence?

Unroll it down the length of the fence to the next corner post. Open the tabs on a T-post one at a time from the bottom to the top of the post. Insert the wire mesh into the bottom tab and squeeze it shut with pliers. Continue attaching the wire mesh from the bottom to the top of each pole.

How do you ensure a fence post is straight?

1. Pulling a string. The string is really called ‘mason’s line. …
2. Set the location of the first and last posts. I start every fence I build by determining the locations of the first and last posts in each run. …
3. Dig in. …
4. Map the rest of the posts. …
5. Brace for it. …
6. Fasten those posts.

Can I set a post without concrete?

Did you know that it is actually completely possible to set wooden posts in your yard without using ANY concrete? It’s true! Setting them without concrete will save you time and money, but there is a correct way to do it in order to prevent rot.

Do fence posts need to be cemented into the ground?

Do Fence Posts Need To Be Set in Concrete? No, fence posts don’t need to be set in concrete, and there are plenty of other ways to fix your posts if this feels a bit too permanent. If you are using wooden posts, concrete may actually be the worst option.

How do you install wire mesh fence on uneven ground?

One of the easiest ways to mount a wire fence on the uneven ground over rough terrain is to dig out the fence line because the ground is forgiving enough, and the difference in the ground’s level is not too dramatic. Measure and mark the boundary with string, then dig away the earth to form a level boundary.

What is the difference between T post and u post?

Steel T-posts and U-posts are used exclusively with wire fencing. T-posts are shaped like the letter T, and U-posts are shaped like the letter U. … You can get away with a little more distance between posts if using barbed wire.

Which side is the finished side of a fence?

The finished side of a fence is often called the “face” while the unfinished side is called the “back.” Regardless of whether you paint it or dress it up, the back of the fence is the one that contains the horizontal fence supports (also called stringers) and the in-ground fence posts.

Article first time published on

How many bags of quikrete do I need for a fence post?

When you account for the fence post what you need is 4 bags. The best way to determine the size of each fence post hole is: The diameter of the hole is 3 times the width of the fence post. The depth of the hole is 1/3 to 1/2 the above ground height of the fence post.

How big of a hole do you need for a 4x4 post?

The diameter of your post hole should be three times the diameter of your post. So, if you’re planning on using a four-inch round or 4×4-inch square post, your post hole will need to be 12 inches in diameter. For a six-foot-high fence post, we would need a hole that’s 36 inches deep and 12 inches in diameter.

How many bags of cement do I need for a fence post?

Most fence post holes will need between 1 – 4 bags of concrete to securely hold the post in place. The best way to determine the size of the hole is: Diameter of the hole is 3 times the width of the fence post.

How deep do post holes need to be?

Dig post hole so diameter of the hole is 3 times the width of the post (i.e., the hole for a 4” wood post should be about 12 inches wide). The depth of the hole should be 1/3-1/2 the post height above ground (i.e., a 6-foot tall fence would require a hole depth of at least 2 feet).

Is 2 ft deep enough for fence post?

2 feet is the minimum depth that you should dig your fence post holes for. To dig the holes one-third to one-half of the post’s aboveground height, is a general formula. The deeper you dig the holes, the more stability your fence has.

How far should wood fence post be apart?

Most fence posts can be spaced 8 to 12 feet apart. While this is a general criteria, it doesn’t cover all scenarios. For instance, high tensile fence can have larger spacing, requiring line posts every 15 to 20 feet for field fence styles, and as much as 20-30 feet for high tensile barbed and smooth wire.

How do you put a fence up without digging?

1. A Metal Spike Anchor and a Sledgehammer. If you are not wanting to dig to set your fence post, a metal spike anchor might be the easiest option. …
2. T-Post Driver. …
3. E-Z Spike. …
4. Steel Posts in the Ground. …
5. Above the Ground Fences.

Can you reuse fence posts with concrete?

Pulling up an existing fence post to reuse can be quite a task. … Posts with concrete at the base are the most difficult to remove and reuse because the concrete base is larger than the post, which makes pulling it up through the ground much harder.

How many bags of gravel do I need for a fence post?

How much gravel do I put in the hole? You should put approximately 2″ to 4″ of gravel in the bottom of the hole making sure that the Post stands 6′ 4″ tall from the ground to the top of the post. How wide should the holes be? An 8″ diameter wide hole should be dug for the posts to be inserted for a solid Fence.

How deep should a 8 foot fence post be?

How Deep Should a Fence Post Be? For an average fence post, about 6 to 8 feet tall, prepare to dig a post hole about 2 feet deep. To install a fence post, you’ll need a shovel or post digger, a 6-foot level, soil, and gravel or crushed stone.

How do you set a 4x4 post without concrete?

Backfilling the fence post hole with gravel is another common alternative to using cement. Start with a hole about the size of the one you’d dig if you were using cement, insert a third of the post’s length into the hole, and then fill with crushed gravel, tamping every five inches until flush.