A mantel should extend a minimum of 3 inches beyond the firebox opening. If the fireplace has facing around the opening, the mantel can also extend 3 or more inches beyond that.

How do you finish Live Edge shelves?

1. Remove the bark and sand the wood. …
2. Bridge splits in the wood with butterfly keys. …
3. Fill any holes in the slab. …
4. Finish and seal the slab.

How do you secure a fireplace mantel?

1. Locate the studs behind the brick, stone, or faux veneer.
2. Drive 1/2in lag screws through each of the studs. …
3. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. …
4. Apply construction adhesive into the holes. …
5. Slide into place, admire, and enjoy!

What is a live edge shelf?

Live edge floating shelves are an interesting addition to any wall in any room. … Live edge refers to a piece of wood that still retains its natural shape from when it was cut from the tree. It might retain both cambium and bark. Place your live edge floating shelf anywhere you need a little decorative storage.

How do you hang a corner shelf without brackets?

Use a kit that is labeled to support more than the weight of the items you plan to place on it. You can also mount shelves using support pins or ledges. A support pin functions the same way as an invisible bracket in a floating shelf kit. It resembles a long rod with a flanged end, and fits into the shelf from behind.

How do you attach a wood mantel to a brick fireplace?

1. Remove the old mantel.
2. Add support by drilling holes for lag shields, then install lag bolts into the brick.
3. Measure carefully and drill corresponding holes for the wood mantel.
4. Push the wooden mantel carefully into place using wood glue for extra support.

How do you support a corner shelf?

Corner shelving should be fixed to the support battens – with the shelf in position, mark underneath the side of the supports onto the shelf. Drill a hole halfway between the marks and the edge of the shelf to take a small screw, and countersink the top side of the shelf if necessary.

How far should a mantel stick out?

A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).

What is a floating mantel?

Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. … Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.

What is code for a fireplace mantel?

The National Fire Code dictates that any combustible material (e.g., wood mantel or similar trim) must be at least six inches from the firebox opening. An additional inch of clearance is needed for every 1/8 inch the combustible material or trim protrudes.

Article first time published on

How far from fireplace should mantle be?

Most housing codes and the National Fire Protection Agency (NFPA) state that the bottom of the mantel must be at least 12” away from the top of the fireplace box. The main factor for distance will come down to the Face Height of your mantel.

How do you attach a mantel to Brick?

Lift the mantel and position it in place, aligning the holes in the back of the mantel with the support rods. Push the mantel onto the rods until the back of the mantle is against the bricks. Gently tap with a small hammer and a small piece of wood if necessary to completely align the mantel next to the brick.

How do you build a floating mantel on a brick fireplace?

1. Prep your surface. For me, that meant staining our fireplace white beforehand. …
2. Create mantel support. …
3. Create a hollow box for your mantel. …
4. Finish the mantel. …
5. Attach your shelf support onto the brick. …
6. Fit your mantel onto the mantel support. …
7. Style your finished mantel!

How do you keep a live edge on wood?

Pour over epoxy resin is your best bet to hold the bark in place if you plan on keeping it. Polyurethane would be another option, but won’t be quite as strong. Oils and waxes seal the wood, but they aren’t going to serve as an adhesive like epoxy would to keep the bark in place.

Do you remove bark from live edge?

For many live edge slabs, we must remove all the bark. It’s especially true if the wood comes from species, like hickory, that loses their bark despite the timing of its cut. … When we have all the bark removed, we’ll use a small nylon or wire brush to scrub away loose or stringy cambium-layer fibres.