The Whirlpool washer Lo FL error code is displayed when water is not detected entering the washer or it’s not filling the washer fast enough. … Make sure the water supply hoses are not kinked or pinched and that screens in the supply line are clear of debris.

How do I fix FL error on my Samsung washer?

If the door fails to unlock after seven tries once the washer cycle is complete, you’ll get the LO or FL code. Begin by unplugging the washer, and force open the door. Check the wiring connections to the door lock/switch, and tighten if needed.

What does LO FL mean on my washer?

The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. If the washer has an F8 E1 error or LO FL error, the door may be locked, and the control may be unresponsive.

What does FL error mean?

The following are common reasons why FL error code appears: You are unable to lock the door. After wash, the door will not open. not properly closing the laundry door before starting a wash cycle. failure to insert the washing machine lid handle into its retaining clips when starting a wash cycle.

How do I fix the LF on my Maytag washer?

LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

What does Fl mean on my air conditioner?

The P2 or FL error code (depending on model) indicates that the drain pan in the unit is full. Under normal operating conditions, the drain pan will not need to be emptied. … There is usually not enough water in the drain pan to cause the air conditioner to shut off.

What does lf mean on my Samsung washer?

LF in the display This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.

Why is my Maytag washer says E01 F09?

Whirlpool Duet Washer Error Code E01 F09 means LONG DRAIN TIME. When your Whirlpool washer goes into drain mode and the drain time is past 8 minutes and not reaching the reset level in the pressure sensor then the valves in the drain are turned off and the drain pump will cease to pump out the water.

What does low FL mean on my Maytag washer?

The F8 E1 or Lo FL error code means your washer is not detecting the correct amount of incoming water. … Press the power button, and the washer will start a drain routine, which takes approximately 8 to 10 minutes, during which time the pump will run continuously. The control will not accept any input during this time.

How do I reset my Maytag washer?

1. Press the “Power/Cancel” button. …
2. Push the appropriate button to choose a new cycle.
3. Press “Start/Pause.” You have now reset your Maytag washer.

Article first time published on

What does Fl mean on front load Whirlpool washer?

Troubleshooting and Repair – Lo FL Error Code – WFW75HEFW. The Whirlpool washer Lo FL error code is displayed when water is not detected entering the washer or it’s not filling the washer fast enough.

How do I reset my Cabrio washer?

Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.

What does low flow mean on a washing machine?

If you only notice low water pressure when using the hot water setting, then you probably have a clogged hot water line (or vise-versa for cold water). The easiest solution to this problem is to replace the clogged line with a new one. Water lines can be purchased either online or at most major home improvement stores.

What are the codes for a Maytag washer?

Error CodeErrorSud or SdThere are too many suds in the washing machine.F5 E2The door is not locking properly.F7 E1Indicates a motor speed sensing error,F8 E1 or LO FLThe washer is sensing a low flow of water.

How do I clean the filter on my Maytag washer?

The quickest way to clean out your filter is to remove it from the unit and soak it in hot water, loosening any clog or trapped residue. If the filter cannot be removed, clean it out with brush. Some filters are disposable, so instead of cleaning them you can just throw them away and put a new one in place.

What does 5d mean on Maytag washer?

This error code indicates excessive detergent suds occurred during the cycle. This could be caused by using too much detergent or not using High Efficiency (HE) detergent. The washer will not be able to spin out water with the excess suds.

What does PE mean on a Samsung washing machine?

PE/PE1 that error related to the top load washing machine That error code related to the internal part ( clutch can’t be detected). Clutch controls the Tub rotation during the washing and spin cycle that error clutches not detected there is no troubleshooting for it.

What does UC mean in Samsung washing machine?

Error CodeCauseUCExcessuve Fluctuation In The Supply Voltage (voltage has fluctuated outside 176-286vAC)UE, E4Unbalanced Error (the washing load in the drum is unbalanced i.e. clothes may have got trapped inside a large towel and resting on one side of the drum)

What does EA mean on a washing machine?

New CodeOld CodeCause1EE7Water level sensor Issue3E 3E1 3E2 3E3 3E4EA EBMotor defectE4E1Water supply error. The appliance is not detecting that the unit is filling with water.4E1 4E24EdWater temperature issue

What does Fl mean on a heater?

Fault CodeConditionActionF-L*Evaporator Not DefrostingCall serviceF2T2 Tank Temperature SensorCall serviceF3Compressor FailureCall serviceF4Fan FailureCall service

What does Fl mean on Kogan aircon?

The dehumidifying effect may be lessened or you may receive the “FL” full water tank alarm if the exhaust hose assembly is not removed when drying mode is being used. It’s heat mode. The heat mode indicator light should illuminate if you press the MODE button.

Why is my GE air conditioner flashing FL?

The FL error most likely indicates that the reservoir that collects the condensate produced when the AC runs is “FULL”.

How do I unlock my Maytag washer?

How to unlock Maytag washer door? If there are no errors with the washer and no components are faulty, you can try and cancel the wash cycle, press and keep holding the CYCLE END or CANCEL button and wait a few minutes and the door should unlock on its own.

What is error F09?

The Whirlpool Duet Washer F09 Error is a overflow condition error. It means the overflow contacts on the water level pressure switch have been closed for more than 60 seconds. … If the pump is running but the washer is not draining check the tub to pump hose and the drain hose for blockage.

What is F9 code on Maytag washer?

Did you receive a F9 E1 or DRN long drain alert? If F9 E1 (drain pump system problem – long drain) appears in display, the washer is taking too long to drain water. The drain may extend more than 4.5″ (114 mm) into standpipe. Check plumbing for correct drain hose installation.

Does Maytag washers have a reset button?

Press and hold the Start/Pause button for 3 seconds. All indicator lights should be off at this point. Reset the Washer: To reset (clear) the washer, rotate the Cycle Selector Knob counter-clockwise (left) to clear any sequence.

Why does my Maytag washer stop mid cycle?

Common solutions for: Maytag Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. … If the lid switch assembly fails, the washer may stop mid-cycle. To determine if the lid switch assembly is defective, use a multimeter to test each of the lid switches for continuity.

Why is my Maytag washer not spinning?

One of the most common reasons for a Maytag top load washer not spinning is an incorrect wash cycle or spin setting. GENTLE, HANDWASH, or DELICATE settings utilize slower spin speeds for more fragile fabrics. Some model washers also allow you to vary the spin speed, making it slower or more rapid, for different loads.

Why does my Whirlpool washer says low detergent?

Detergent Level Low – This will light (yellow) if there is enough detergent in the Load & Go™ cartridge for only a few more cycles.

How do I reset my Whirlpool front load washer?

Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.

How do you fix the F code on a Whirlpool Cabrio washer?

An F/dL error code indicates a problem with the door lock. The error code will pop up when the door fails to lock. The washer will display the error code after six attempts to lock the door. To fix the issue, the door lock assembly needs to be inspected for loose or broken wires and other signs of damage.