Class I, Division 2 or Zone 2 classified locations. An area where ignitable concentrations of flammable gases, vapors or liquids are not likely to exist under normal operating conditions. In this area the gas, vapor or liquids would only be present under abnormal conditions (most often leaks under abnormal conditions).

What is an example of a Class 1 Division 2 location?

Industries that typically require Class 1, Div 2 approval include: Process Industry. Oil and Gas Industry. Gas Pumps, Gas Stations.

What is the difference between Zone 0 1 and 2?

Zone 0: Explosive atmosphere for more than 1000h/yr. Zone 1: Explosive atmosphere for more than 10, but less than 1000 h/yr. Zone 2: Explosive atmosphere for less than 10h/yr, but still sufficiently likely as to require controls over ignition sources.

Does Class 1 Div 2 require explosion proof?

A Class I Division 2 light are not held to as high of a standard as Division 1 products. To meet the requirements for Division 2, a light does not have to be able to contain an explosion. Instead, they must be found to be unable to cause an explosion in environments for which they are approved to be used.

What's the difference between Class 1 Div 1 and Class 1 Div 2?

Class 1 Hazardous Locations refer to facilities which deal with flammable gases, vapors, and liquids. Division 2 specifies that these flammable materials are handled, processed, or used in the defined hazardous location, but are not normally present in concentrations high enough to be ignitable.

What is a Class 2 Div 2 area?

Class II locations consist of locations where combustible dusts may exist that have the potential to become flammable or ignitable. … Division 2 is also a subset of Class II and is classified as an area where the explosive or flammable combustible dusts mentioned above are not likely to exist during regular operation.

Is NEMA 4X good for Class 1 Div 2?

We recommend electrical enclosures meet or exceed a NEMA rating of Type 4 or Type 4X for use in a Class1 Div2 hazardous location when used with appropriate purge systems.

What is Gas Group IIC?

– Group IIA—Atmospheres containing propane, or gases and vapors of equivalent hazard. … – Group IIC—Atmospheres containing acetylene or hydrogen, or gases and vapors of equivalent hazard. n Group III—Equipment intended for use in places. with an explosive dust atmosphere.

What is a Class 1 location?

Class I Locations A “Class I Location” is created by the presence of flammable gases or vapors in the air in sufficient quantities to be explosive or ignitable. When these materials are found in the atmosphere, a potential for explosion exists if an electrical or other source of ignition is present.

What makes a light explosion proof?

To be certified, explosion-proof lights typically will be made of durable, non-sparking material, a very thick glass globe over the bulb, and other features to ensure that the worker and the surrounding environment remains safe should an ignition occur inside the light.

Article first time published on

Is intrinsically safe the same as explosion proof?

WHAT IS INTRINSIC SAFETY AND EXPLOSION PROOF? … Therefore, Intrinsically Safe means that an apparatus, such as a temperature transmitter is not capable of causing an explosion. Explosion Proof means that should an explosion occur, it will be contained within an enclosure.

How do you tell if a motor is explosion proof?

An explosion proof motor is clearly marked with a nameplate that identifies its suitability for a given hazardous environment. Depending on the agency certifying the motor, the nameplate will clearly indicate the hazardous location Class, Division, and Group for which the motor is suited.

What areas are Zone 1 and 2 in London?

Zone 1 covers all of Central London. Zone 2 encircles zone 1 and covers a large swathe of the inner London suburbs.

What is Zone 1 and Zone 2 in oil and gas?

Zone 1 is an area in which an explosive atmosphere is likely to occur occasionally in normal operation. … Zone 2 is a place in which an explosive atmosphere is not likely to occur in normal operation but, if it does occur, will persist for a short period only.

What areas are Zone 2?

• Fulham, SW6. Fulham has three stations within Zone 2; Parsons Green and Fulham Broadway on the District Line and Imperial Wharf for the London Overground. …
• Wapping, E1W. Wapping in East London is a highly desirable place to live. …
• Hammersmith, W6. …
• Clapham, SW4. …
• Find a place to live in zone 2.

What NEMA 7 enclosure?

NEMA 7 enclosures are designed to contain an internal explosion without causing an external hazard. These enclosures are intended for indoor use in hazardous locations classified as Class I, Division I, Groups A,B,C, or D.

What is the most hazardous classification on a job site?

Class I and Class II Divisions are further subdivided into Groups A, B, C, and D. Group A is considered the most hazardous, with Group D being the least hazardous for gases and vapors. The explosive characteristics of the air mixtures of gases, vapors, or dusts vary with the specific material involved.

Is NEMA 12 explosion proof?

A NEMA 12 enclosure is not explosion-proof. … These enclosure types are designed to offer protection in indoor environments with explosion hazards from flammable gases or vapors.

What NEMA 5 rating?

NEMA 5 enclosures are intended for indoor use primarily to provide a degree of protection against settling airborne dust, falling dirt, and dripping non-corrosive liquids. water during occasional, temporary submersion at a limited depth.

Is NEMA 4X dust tight?

NEMA 4 is watertight and dust-tight for inside and outdoor applications. NEMA 4X is everything listed, plus corrosion-resistant. … 4X also adds protection against corrosion.

What is a Class 2 Division 1 malocclusion?

▪ Class II Division 1 is when the maxillary. anterior teeth are proclined and a large overjet is present. ▪ Class II Division 2 is where the maxillary. anterior teeth are retroclined and a deep overbite exists. Class II Malocclusion.

What are fibers and Flyings?

Easily ignitable fibers or flyings present a fire but not an explosion hazard. An example of this type of material is the cotton lint that accumulates in the lint trap of clothes dryers. Listed clothes dryers are designed so that even if the lint ignites, the fire will be contained within the dryer enclosure.

Which of the following is listed as a Class 2 hazardous material?

Commonly transported class 2 dangerous goods include oxygen, natural gas, carbon dioxide, lighters, and aerosols.

What does Class 1 Group D mean?

Class I Group D locations are atmospheres containing elements such as Gasoline, Hexane, Naphtha, Benzine, Butane, Propane, Alcohol, Acetone, Benzol, Lacquer Solvent Vapors or Natural Gas.

What is ATEX environment?

ATEX generally refers to the hazard of explosive atmospheres occurring in the workplace due to the presence of flammable gasses or combustible dust mixed in air, which can give rise to the risk of explosion.

What is dust group?

Like gas, dusts are grouped in order to effectively identify the risks of ignition and to identify the severity of explosion. The size of the dust particles is 500 micro meter or less. Dust can remain suspended in air and may settle due to its own weight.

Is gas Group IIC better than IIA?

The hazard level of the gases increases from gas group IIA to IIC with group IIC being the most severe.

What is flameproof lighting?

In other words, flameproof equipment prevents the ignition of surrounding flammables in the hazardous area. … Flameproof is one of many explosion protection techniques extensively used for light fittings, JBs, and motors in hazardous areas.

Are LED light explosion proof?

Yes, some LED light fixtures are explosion proof. If you choose the correct LED light fixture for your location, with the help of an LED lighting partner to ensure it is the appropriate luminaire, then LED lighting is the perfect choice for your hazardous location.

Are LED lights safe for paint booths?

Choosing the Best Lighting for Your Paint Booth That’s not only a huge swing in energy savings; LED lights give your finishes a truer color. They are safer and don’t present the fire and explosion hazard that overheated bulbs do when coming into contact with paint chemicals.

Is ATEX intrinsically safe?

Intrinsic safety is widely used in Europe as a means of installing equipment in hazardous areas, and ATEX deals extensively with intrinsic safety. … ATEX is a European standard developed in part by the International Electrotechnical Commission (IEC).