Pure linseed oil or tung oil are better suited for treating hardwood worktops as they penetrate timber more effectively than other natural oils. Though it may take a long time, these rub-in oils will naturally dry or cure on their own.

What should I treat my oak worktop with?

Use linseed or Danish oil (available from DIY stores) and a lint-free cloth – microfibre works well. Pour a little oil directly onto the worktop and, using the cloth, spread it over the surface until you have a very thin and even layer.

Do you have to treat oak worktops?

Hardwood worktops must be thoroughly treated with at least three coats of protective wood oil, to all sides (including the underside), prior to installation. It is also beneficial to apply as many coats as possible to the end-grain of the worktops as this is the area which will absorb the most moisture.

How do I protect my oak worktops?

We recommend using Danish oil, which has been specially formulated to protect your worktops and help them last longer. Without regular oiling, the surface is vulnerable to staining which looks unsightly and can lead to additional problems.

What is the best varnish for wooden kitchen worktops?

For the best worktops, we prefer using acrylic varnish. In particular, we recommend using Spar varnish, which is used to protect items that are near the water like wooden boats, yachts, decks and beach chairs. If it’s good enough to keep water out of yachts, its perfect for kitchen worktops.

Can you use Danish oil on oak?

Danish Oil is completely non-toxic and food safe when dry which means in can be used on all oak items and in all environments.

Which oil is best for oak worktops?

Linseed or Tung Oil Pure linseed oil or tung oil are better suited for treating hardwood worktops as they penetrate timber more effectively than other natural oils. Though it may take a long time, these rub-in oils will naturally dry or cure on their own.

How do you waterproof a wood countertop?

Apply a maintenance coat of linseed oil every four weeks. A lightly used countertop may only need to be touched up every six to eight weeks. The linseed oil adds hardness and water resistance. You can tell that a new coat is needed by splashing a few drops of water onto the surface.

How can I make my oak worktop waterproof?

1. STEP 1: APPLY A HARD PRIMER FOR WOODEN WORKTOPS. …
2. STEP 2: APPLY A VARNISH: PRODUCT FOR PROTECTING AND WATERPROOFING A WOODEN WORKTOP. …
3. STEP 3: AFTER PROTECTION, MAINTENANCE OF A WOODEN WORKTOP.

How often should you oil oak worktops?

With regular oiling, real wood worktops should last for many years and will continue to mature in colour as you apply fresh coats of oil. It is recommended that for the first six weeks after installation, your worktops are oiled as regularly as possible, then approximately every three months thereafter.

Article first time published on

How often should I oil my wood countertop?

When first oiling the worktop after installation, it is important to build up coatings (2-3 before installation and 4-5 coats after installation), but when re-oiling for maintenance purposes you would only need to apply 2-3 coats, depending on how worn out your wood worktop is.

Can I use Danish oil on kitchen worktops?

A great way to stop your worktop from warping or bowing, the application of Danish Oil to your worktop will also make it water resistant. With a truly natural look, Danish Oil won’t make your worktop shiny like varnish; it’ll simply enhance its natural good looks.

How do you seal Oak?

1. Apply two coats of Rockler’s Mission Oak Wipe-On gel stain.
2. Seal with shellac and scuff-sand when dry.
3. Apply a topcoat of your choice.

How do I keep my wooden worktop from turning black?

On kitchen worktops pay particular attention to the wood end grain. If using Treatex keep applying the the Hardwax Oil while the oil is still wet until the oil is no longer absorbed by the wood. This will ensure that the oil has penetrated deeply into the wood grain and keep those unsightly black water marks at bay.

Can you stain oak worktops?

Staining worktops is not generally recommended for a number of reasons. … Notwithstanding these risks, if you are adamant that you want to change the colour of your solid wood worktop or to breathe new life into a wood worktop, an appropriate, safe stain can be a good way to achieve a result.

How do you remove the stickiness from a Danish oil worktop?

If food or liquid have congealed into a sticky residue, avoid using spray disinfectant, especially if you have recently treated your wooden worktops with Danish oil as this can exacerbate the stickiness. Instead, make a dilute solution of warm water and lemon juice and wipe down the area with a clean, lint-free cloth.

How do you protect a wood worktop from a sink?

Use an appropriate sealant to seal your sink into place and create a water-tight seal. Oil the area around the sink every 6-8 weeks to ensure the wood is well protected. Be sure to wipe down any water splashes / spills as quickly as possible.

How do you prepare oak for oiling?

Oiling Consideration If oak is being oiled it is a good idea to sand it with sandpaper that is no finer than 150 grit. The reason for this is that the pores of the wood are more open thus allowing the oil to sink into the wood better.

Which is better Danish oil or linseed oil?

Danish oil and Teak oil dry faster than linseed oil, which is traditionally used on willow cricket bats. The finish they provide is also much more resilient. If your wood already has linseed oil on it, it’s best to carry on using it.

What are the disadvantages of Danish oil?

• Need Regular Maintenance. …
• Less Durability. …
• Time Consuming. …
• Can only Apply to Bare woods. …
• Can Occur Sudden Ignition. …
• Doesn’t Smoothen the Wood Grain.

Can you use linseed oil on oak?

Boiled Linseed Oil is used to give a mellow, patinated finish to new or stripped bare interior wood. … Suitable for use on all types of wood, except exterior oak, it can also be used as a traditional sealer for terracotta tiles, stone floors and other porous surfaces before waxing.

What is Danish oil good for?

A superior penetrating linseed oil finish that is polymerized for fast and easy application on interior woodwork and furniture. It is also ideal for wood paneling, cabinets, salad bowls, wood utensils, butcher blocks and surfaces that come in contact with food.

Can you use varnish on kitchen worktops?

Varnish – though a good choice in some situations – is generally not advised for use in a kitchen. Timber varnishes dry to a relatively brittle, plasticky finish, which can be scratched easily by kitchen knives or cracked by heavy items; the finish is also not very resistant to heat damage.

How do I waterproof my kitchen wood?

1. Use linseed or Tung oil to create a beautiful and protective hand-rubbed finish.
2. Seal the wood with coating of polyurethane, varnish, or lacquer.
3. Finish and waterproof wood simultaneously with a stain-sealant combo.

How do you protect wooden kitchen worktops?

To maintain your worktops quality wipe worktops down regularly with a damp (not wet), lint-free cloth, warm water and a small amount of soap. We do not recommend using multi-purpose cleaning products which contain chemicals as this may damage the worktops. Please also avoid the use of scouring pads.

How do you seal wood in a kitchen?

1. Sand the item with 320-grit sandpaper until smooth. …
2. When using an oil finish, apply a generous amount to a cloth. …
3. Apply wax with a cloth until the surface is covered. …
4. Allow newly finished pieces to dry and cure fully.

How do you seal and stain wood countertops?

1. Sand off any stain and polyurethane starting at 60-grit and going to 220-grit sandpaper.
2. Apply a thick coat of the stain.
3. Let it sit for 15 minutes or so.
4. Wipe off any excess.
5. Let it dry overnight.
6. Apply one coat of quick-dry polyurethane.
7. Lightly sand your wood countertop with 220-grit sandpaper.
8. Dust.

How do you protect wooden countertops from heat?

Silicone protectors typically have nonslip exteriors that help prevent your hot pans from sliding around. And they can be heat resistant up to 446 degrees Fahrenheit. Bamboo and wooden countertop protectors aren’t as heat resistant as silicone, but they can usually handle heat up to 400 degrees Fahrenheit.

Should I sand between coats of Danish oil?

Danish oil dries slowly, so wait overnight before recoating. And it goes on thin, so apply a minimum of three coats. You don’t have to worry about brush marks, but you’ll get an even smoother finish by lightly “wet” sanding between the second and third coats.

How long after oiling worktop can I use it?

Flip the worktop over and repeat the procedure, applying coat to the bottom face and end grain. Leave to dry (allow 6-8 hours between coats).

Should you oil both sides of worktop?

The worktop needs at least six coats of finishing oil on both sides prior to installation. Try and do this in a warm environment otherwise the oil will be slow to dry.