When asking the question is a toilet tank universal, the short answer is no. While in certain brands they can be interchangeable, the overall consensus is that your toilet tank is fitted to your toilet model. When looking to purchase a new tank, you need to learn the measurements and model number.

How do you separate a toilet tank from the bowl?

Disconnect the tank from the bowl by removing the bolts found inside the bottom of the tank. Using a large screwdriver to support the head on the bolt, then turn the nut under the tank with an adjustable wrench (Image 2) until it is possible to remove the entire bolt from the tank. Repeat the process on all the bolts.

Are there different sizes of tank to bowl gaskets?

The 2 inch Tank to Bowl Gasket is universal to fit most 2 inch two-piece toilet tanks. The universal sponge rubber design measures: 2-1/8 inch inner diameter, 3-1/2 inch outer diameter and 1-1/4 inch thick.

Why is my toilet leaking from the tank to the bowl?

The most common cause of a leaking toilet tank is when the flapper fails to seat properly and form a tight seal against the valve seat. This lets water leak from the tank into the bowl. It may be caused by the flapper being out of position. … If the water level has fallen below your mark, the flush valve is leaking.

Are all toilet tank seals the same?

Tank to Bowl Gaskets It may be time to replace your tank to bowl gasket. Manufactured in a high quality, chlorine resistant rubber, the Korky tank to bowl gaskets are universal to fit most toilet tanks.

Can I only replace toilet tank?

If your toilet tank is cracked, there is no way to repair the damage, so it must be replaced. Replacing a toilet tank is a task most homeowners can do without a call to the plumber. Because the tanks and bowls may be sold separately, you can often buy just the tank.

What is a tank to bowl kit?

The Toilet Tank to Bowl Hardware Kit contains all of the necessary accessories to install a tank to bowl gasket. … Easy to install, the 465 toilet parts include: (3) Stainless Steel Bolts, (3) Stainless Steel Washers, (3) Stainless Steel Nuts and (3) Rubber Washers.

Are toilet tank bolts universal?

Are Toilet Tank Bolts Sizes Standard? Toilet tank bolts help to seal your toilet tank such that it does not leak. They are durable and often in the same sizes and lengths. More often, toilet tank bolts are standard and will fit most types of toilet tanks.

Can you mix and match toilet bowl and tank?

There are a few models that can interchange tanks and bowls, but most are configured to work as a set, as indicated in our product showcase. If you mix and match yourself, the toilet may not flush at all. Tanks and bowls can not be mixed.

What tools do I need to remove a toilet tank?

In addition, gather any equipment you need to remove a toilet such as: a sponge, bucket, utility knife, stiff wire brush, hacksaw, putty knife, wrenches, ratchet wrench and sockets, and rags.

Article first time published on

Can you install a toilet yourself?

All you need are a few hours, a helper and the right tools and toilet parts for the job. Before you begin learning how to install a toilet, choose your new toilet and, if you aren’t replacing an existing toilet, make sure you have plumbing ready for the new installation.

Is it safe to leave a toilet off overnight?

Yes, absolutely, fumes can be harmful when replacing a toilet, but they can be kept at a minimum and shouldn’t pose a health risk if you work reasonably quickly and keep the drainpipe covered between removal and installation. Sewage gases are toxic and also flammable.

How do I fix a leaking toilet tank?

1. Introduction.
2. Turn off the water at the shutoff valve below the tank.
3. Drain the tank completely.
4. Hold one of the tank bolt nuts.
5. Unscrew the tank bolts with the screwdriver.
6. Remove the tank from the bowl and lay it down.
7. Remove the old spud washer.
8. Insert the new spud washer.

When I flush the toilet water comes out the bottom of the tank?

One reason for a toilet leak from the base might be a loose connection where the tank meets the toilet. … Shut off the water at the valve, then flush and hold the handle until all the water has drained from the tank. Remove the old bolts and washers. Clean and dry the area, then install new washers and bolts.

What size gasket does my toilet need?

To determine the correct width for your wax ring, simply turn your toilet bowl on its side, and measure the opening on the bottom of your toilet, called the “elbow neck.” Whatever width this measurement is, use that width wax ring. E.g. if the elbow neck measures 3 inches, use a 3-inch wax ring.

What size is the toilet tank nut?

The stainless steel nuts and washers are also included for complete replacement of all old hardware. Tank Bolts are proven durable, and the 5/16” size x 2 ¾” length will fit most brands and models. Repair your rocking toilet tank with new toilet bolts.

How much does a toilet tank cost?

The average price for Toilet Tanks ranges from $40 to $2,000.

How do you get a locking nut off the bottom of a toilet tank?

1. Step 1: Close the water supply line.
2. Step 2: Place a towel under the toilet tank.
3. Step 3: Take the lid off the top of the tank.
4. Step 4: Drain the water from the tank.
5. Step 5: Remove the plastic coupling.
6. Step 6: Unscrew the nut by turning it clockwise.

How much does it cost to replace a toilet tank?

A replacement tank will range from $50 to $100, not including the labor to install it. A professional plumber can put in a new tank in one to two hours for a total cost of $45 to $300. Total project price will depend on minimum charges as well as whether the internal tank parts also require replacement.

Can you mix toilet tanks?

It is unlikely that tanks will be interchangeable if you replace a toilet tank with one from a different manufacturer. Problems with mismatched tanks and bowls include hardware not lining up and poor balance on the bowl. Even if the bolts line up, the new tank may leak or be wobbly.

Does Eljer still make toilets?

Today Eljer® continues to offer innovative toilets as well as beautiful and functional bathtubs, whirlpools, and air baths.

Can you put a new cistern on an old toilet?

So for some people, the answer to can you just replace the cistern on a toilet is a yes, but if you have any doubts it makes a lot more sense to bring in the experts so that there are no errors that might end up costing you even more.

How do I know what type of toilet I have?

Finding your toilet manufacturer and/or model number: Carefully remove the toilet tank lid and set it gently on the floor, with the bottom facing up. Look for the manufacturer name or a number on the bottom side of the water tank lid.

How do I keep my toilet tank bolts from rusting?

The best way to stop toilet tank bolts from rusting is by using all-brass bolts and nuts to secure the tank to the toilet bowl. Unlike steel, brass won’t rust. If you are replacing rusted toilet tank bolts, make sure to use a set of brass bolts.

How tight should a bowling tank be?

Bolts Don’t Have to Be Extremely Tight It’s important to keep in mind that the toilet tank is not intended to take weight and strain. The tank-to-bowl bolts are merely there to ensure the rubber seal between the tank and bowl is snug and leakproof. Tank bolts do not need to be tightened to an extremely snug position.

How tight do you tighten a toilet tank?

Most toilets have a space between the bottom of the tank and the top of the bowl anywhere from a ¼ of an inch to a ½ inch. Tighten too loosely and the tank will leak underneath the rubber washers and down the bolts; tighten too much and risk the tank cracking.